Mohawk A-7 Скачать руководство пользователя | Manualshive

Страница: 3 / 74

background image

MOHAWK MODEL A-7

ii

APPENDAGE:

Rev (6/19/2012)

LIFT

ENVIRONMENT:

Mohawk

prohibits the outdoor installation of this standard lift, which is APPROVED FOR INDOOR USAGE ONLY,

in a normal garage type environment. Any concerns in applications that expose the lift to additional environmental
effects, such as paint booths, wash bays, outdoors, high or low temperatures, etc. must be addressed to our engineering
department, where provisions could/may be made to the lift to accommodate the area of use. Our engineering
department must be made aware in advance of these conditions and any additional code requirements that must be met.

Also,

the foundation for which this lift must be installed on must comply to the minimum specifications as set forth in

this manual. Any drainage slopes in the bay where the lift is to be installed must be directed away from the posts to
prevent water accumulation at the post bases.

Standard foundation flooring and anchorage specifications are contained within this manual. For installation
within a seismic area, a qualified person must be consulted to address seismic loads and other local or state
requirements.

ACCESSORIES:

All accessories (i.e. Lifting Pads, Height Adapters, Wheel Adapters, Turf Adapters) supplied with this lift are
to be used on this lift only. Accessories from other lifts are not acceptable and could result in injury to the
user.

If attachments, accessories or configuration modifying components are

used on this lift and, if they are not

certified for use on this lift, then the certification of this lift shall become null and void. Contact the participant
(Mohawk Resources Ltd.) for information pertaining to certified attachments, accessories or configuration modifying
components.

LOCK WARNING:

Latches do not automatically reset after disengagement. After the latches have been manually disengaged, this
lift must be raised approximately 2 inches to reactivate the latches.

LOCKOUT/TAGOUT REQUIREMENTS:

The start switch provided with this unit must not be used as a primary disconnecting means. A separate
disconnecting means must be

provided in accordance with all applicable codes. It is the responsibility of the

owner/user of this unit to provide a proper lockout/tagout device for this unit before or during installation in
conformance to ANSI Z244.1 and any local/state/national electrical codes and any OSHA regulations.

PROPER

SELECTION OF POWER SUPPLY CORD:

Acceptable Cord Types:

SO, SEO,STO, SOW, SEOO, SOW-A

Cord Size:

12/4

Cord Ampacity:

20 Amps

Cord Wiring: Use Female NEMA Plug supplied with lift and wire as follows (See Diagram Below),
G: Ground (green)
W: Neutral (white)
X: 208 VAC Hot,

110 VAC to ground (Red)

Y:

208 VAC Hot, 110 VAC to ground (Black)

Face of Plug Represented:

«
1
2
3
4
5
...
»

Содержание A-7











































































Отзывы:

Нет отзывов

Похожие инструкции для A-7

Бренд: Zehnder Rittling Страницы: 36

Бренд: YASKAWA SIEMENS Страницы: 373

Бренд: SMT Страницы: 24

Бренд: ESAB Страницы: 23

Бренд: Mark Climate Страницы: 60

GreenCable Mat Series

Бренд: Flextherm Страницы: 20

Бренд: MIDWEST FASTENERS Страницы: 2

Бренд: M-system Страницы: 19

Devicenet R7F4DD-DA16A-H

Бренд: M-system Страницы: 7

Бренд: Maco Страницы: 40

Бренд: Dibipack Страницы: 41

Бренд: NEC Display Solutions Страницы: 4

InverArc 160 Plus

Бренд: HTP Страницы: 10

Бренд: HURNER Страницы: 57

Бренд: ALFIN Страницы: 16

Бренд: iWeld Страницы: 90

ofs Fitel EZ-Terminator

Бренд: Furukawa Страницы: 28

Бренд: Zepro Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды