Mohawk A-7 Скачать руководство пользователя | Manualshive

Страница: 26 / 74

background image

MOHAWK MODEL A-7

18

TROUBLE SHOOTING, CONTINUED

POSSIBLE CAUSE

SOLUTION

RAISING UNEVEN, CONTINUED

SHOP FLOOR UNEVEN

USE SPECIAL LIFT PADS. SEE FIGURE 12.

DIVERTER VALVE

REMOVE BLEED LINE FROM THE TOP OF THE OFF SIDE CYLINDER AND CAP
USING MOHAWK PART # 601-420-001. IF THE UNIT CONTINUES TO DRIFT DOWN
THE DIVERTER PULL VALVE WILL NEED TO BE CLEANED OR REPLACED.

OFF SIDE CYLINDER

REMOVE BLEED LINE FROM THE TOP OF THE OFF SIDE CYLINDER AND CAP
USING MOHAWK PART # 601-420-001. IF THE UNIT NO LONGER DRIFTS DOWN
THE OFFSIDE CYLINDER WILL NEED TO BE SERVICED..

MAIN SIDE CYLINDER

PERFORM HYDRAULIC SAFETY CHECKS. CHECK FOR INTERNAL HYDRAULIC
LEAKS

SLOW DRIFT DOWN

SAFETIES NOT ENGAGED

RAISE UNIT TO RE-ENGAGE SAFETIES. THEN LOWER UNIT ONTO SAFETIES.

POWER UNIT LOWERING VALVE
CONTAMINATION

BACK FLUSH POWER UNIT: PULL DOWN ON THE LOWERING HANDLE, AND
THEN ENGAGE THE UP BUTTON AT THE SAME TIME. RUN UNIT APPROX. 10
SECONDS

DIVERTER VALVE

REMOVE BLEED LINE FROM THE TOP OF THE OFF SIDE CYLINDER AND CAP
USING MOHAWK PART # 601-420-001. IF THE UNIT CONTINUES TO DRIFT DOWN
THE DIVERTER PULL VALVE WILL NEED TO BE CLEANED OR REPLACED.

OFF SIDE CYLINDER

REMOVE BLEED LINE FROM THE TOP OF THE OFF SIDE CYLINDER AND CAP
USING MOHAWK PART # 601-420-001. IF THE UNIT NO LONGER DRIFTS DOWN
THE OFFSIDE CYLINDER WILL NEED TO BE SERVICED..

EXTERNAL HYDRAULIC LEAKS

NOTE: TIGHTEN ALL FITTINGS PER SPECIFICATIONS

MAIN SIDE CYLINDER

THOROUGHLY CLEAN THE CYLINDER. VERIFY LEAK ORIGIN. FITTINGS ARE
TO BE TIGHTENED PER SPECIFICATIONS

OFF SIDE CYLINDER

THOROUGHLY CLEAN THE CYLINDER. VERIFY LEAK ORIGIN. FITTINGS ARE
TO BE TIGHTENED PER SPECIFICATIONS.

BAD FLAIR OR FITTING

REMOVE THE HYDRAULIC LINE AND INSPECT FLAIR AND FITTING FOR
DEFORMATION. REPLACE IF NEEDED.

BAD O-RING (O-RING TYPE FITTINGS)

CHANGE O-RING

LOOSE PIPE FITTING

REMOVE, RESEAL, AND RE-INSTALL FITTING.
SEAL ALL PIPE FITTING CONNECTIONS WITH THREAD SEALANT MOHAWK
PART # 601-610-002 NOTE

: DO NOT USE TEFLON TAPE.

MECHANICAL LOCK RE-ENGAGES

CHAIN BREAK SAFETY CABLE NEEDS
ADJUSTMENT

TENSION IN CABLE MAY BE TO TIGHT. REFER TO FIGURE 14.

MECHANICAL LOCK HARD TO PULL

CHAIN BREAK SAFETY CABLE NEEDS
ADJUSTMENT

TENSION IN CABLE MAY BE TO TIGHT. REFER TO FIGURE 14.

FLIPPER STICKING ONTO LOCK BAR

APPLY A SMALL AMOUNT OF LUBRICANT TO THE LOCK BAR WHERE THE
FLIPPER RIDES. (DO NOT USE HEAVY GREASE)

«
...
24
25
26
27
28
...
»

Содержание A-7











































































Отзывы:

Нет отзывов

Похожие инструкции для A-7

Бренд: Orion Welders Страницы: 51

Бренд: WAGO Страницы: 20

Бренд: Northern Industrial Tools Страницы: 18

ZIP CHAIN LIFTER

Бренд: Tsubaki Страницы: 40

iO-GRID M GFDO-RM01N

Бренд: DAUDIN Страницы: 25

Бренд: A-T Controls Страницы: 19

Бренд: iWeld Страницы: 10

Бренд: Amplicon Liveline Страницы: 42

PressureMAT PMAT2

Бренд: PendoTECH Страницы: 48

RaptorX-SL1200-S15

Бренд: CNC-Step Страницы: 102

Бренд: Thermal Dynamics Страницы: 144

Бренд: ICP DAS USA Страницы: 6

Бренд: SMA Страницы: 64

CLI U12 SD0(W/L/F/P) 1110 NG B/U

Бренд: Velux Страницы: 50

Бренд: KSF Страницы: 32

Copperloy EDGE-OF-DOCK SEL Series

Бренд: JH Industries Страницы: 42

Бренд: Raven Страницы: 47

Бренд: Elettro CF Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды