Mohawk A-7 Скачать руководство пользователя

Страница: 25 / 74

MOHAWK MODEL A-7

TROUBLE SHOOTING

WARNING:

NEVER ATTEMPT TO LOOSEN HYDRAULIC FITTINGS, OR OVERRIDE SAFETY DEVICES IN AN

ATTEMPT TO CORRECT A PROBLEM. ALL TESTS ARE TO BE PERFORMED WITH

VEHICLE.

HYDRAULIC SAFETY CHECK

NOTE: THE HYDRAULIC SAFETY CHECK IS TO BE PERFORMED WITH NO VEHICLE ON THE UNIT.

CONTACT YOUR LOCAL MOHAWK DISTRIBUTOR OR THE MOHAWK FACTORY IF EITHER TEST FAILS.

MAINSIDE SAFETY CHECK:

RAISE THE UNIT APPROXIMATELY 3 FEET

DISENGAGE THE

OFFSIDE

MECHANICAL SAFETY

LOWER THE UNIT ONTO THE

MAINSIDE

MECHANICAL

SAFETY

WHILE CONTINUING TO HOLD DOWN THE POWER UNIT
LOWERING HANDLE, OBSERVE THE

OFFSIDE

CARRIAGE FOR MOVEMENT. THE UNIT HAS CHECK
OUT OK IF THERE IS NO MOVEMENT (

OFFSIDE

CARRIAGE DOES NOT CONTINUE TO LOWER)

OFFSIDE SAFETY CHECK:

RAISE THE UNIT APPROXIMATELY 3 FEET

DISENGAGE THE

MAINSIDE

MECHANICAL SAFETY

LOWER THE UNIT ONTO THE

OFFSIDE

MECHANICAL

SAFETY

WHILE CONTINUING TO HOLD DOWN THE POWER UNIT
LOWERING HANDLE, OBSERVE THE

MAINSIDE

CARRIAGE FOR MOVEMENT. THE UNIT HAS CHECK
OUT OK IF THERE IS NO MOVEMENT (

MAINSIDE

CARRIAGE DOES NOT CONTINUE TO LOWER)

POSSIBLE CAUSE

SOLUTION

NOT RAISING LOAD

LOW HYDRAULIC FLUID LEVEL

LOWER UNIT. REMOVE RESERVOIR BREATHER CAP. FILL UNIT TO WITHIN 1/2
INCH BELOW PORT. USE DEXRON III TRANSMISSION / HYDRAULIC FLUID.

PRESSURE RELIEF ADJUSTMENT

CONTACT MOHAWK SERVICE DEPARTMENT.

PRESSURE RELIEF CONTAMINATION

REFER TO POWER UNIT SPECIFICATIONS. REMOVE AND CLEAN DEBRIS FROM
VALVE ASSEMBLY. SEE FIGURE 13.

VOLTAGE TO POWER UNIT

REFER TO POWER UNIT SPECIFICATIONS. CONSULT AN ELECTRICIAN

UNIT OVERLOADED

VEHICLE IS TO HEAVY TO BE RAISED

NOT LOWERING

MECHANICAL LOCKS ENGAGED

RAISE UNIT. DISENGAGE MECHANICAL LOCKS.

UNIT UNEVEN (SIDE TO SIDE)

RAISE UNIT TO FULL HEIGHT TO EQUALIZE. THEN LOWER
OR
USE DIVERTER VALVE TO EQUALIZE

POSTS OUT OF SQUARE

VERIFY LEVEL ASSEMBLY. MAKE ANY AND ALL NECESSARY ADJUSTMENTS.
SEE FIGURE 7 & 8.

DEBRIS IN POSTS (TOOLS ETC.)

CLEAN UNIT

OBSTRUCTION UNDER VEHICLE OR LIFT

REMOVE OBSTRUCTION.

RAISING UNEVEN

RULE OF THUMB:

IF THE MAIN SIDE IS HIGH, RUN UNIT TO FULL HEIGHT. IF THE MAIN SIDE IS LOW, LOWER UNIT TO

FLOOR. ALLOW TIME FOR THE OFF SIDE TO EQUALIZE.

AIR IN SYSTEM

BLEED UNIT. REFER TO BLEEDING PROCEDURES.

CARRIAGE BEARINGS CONTACTING CARRIAGE
STOPS

CARRIAGE BEARINGS ON THE MAIN SIDE MUST NOT CONTACT CARRIAGE
STOPS. (RESULT OF INCORRECT CYLINDER SHIMS.) SEE

“

SHIMMING FOR

CHAIN TENSION” SECTION. SEE FIGURE 9.

POSTS OUT OF SQUARE

VERIFY LEVEL ASSEMBLY. MAKE ANY AND ALL NECESSARY ADJUSTMENTS.
SEE FIGURE 7 & 8..

CYLINDER SHIMS

VERIFY CYLINDER SHIMS. MAKE ANY AND ALL NECESSARY ADJUSTMENTS.
SEE

“

SHIMMING FOR CHAIN TENSION” SECTION. SEE FIGURE 9.

SHOP FLOOR UNEVEN

VERIFY PROPER INSTALLATION OF MAIN SIDE POST. MAIN SIDE TO BE ON
HIGH SIDE. SEE FIGURE 11.

Содержание A-7











































































Результаты поиска

Содержание A-7

Отзывы:

Похожие инструкции для A-7

Бренды по названию

Популярные бренды

Mohawk A-7, Руководство пользователя

Результаты поиска

Содержание A-7

Отзывы:

Похожие инструкции для A-7

Бренды по названию

Популярные бренды