background image

MOHAWK MODEL A-7 

 

vi 

 

MOHAWK WARRANTIES 

EFFECTIVE DATE: 12/1/2015* 

READ THIS WARRANTY IN ITS ENTIRETY 

 

GENERAL WARRANTY INFORMATION: 

MOHAWK’S  OBLIGATION  UNDER  THIS  WARRANTY  IS  LIMITED  TO  REPAIRING  OR  REPLACING  ANY  PART  OR  PARTS 
RETURNED  TO  THIS  FACTORY,  TRANSPORTATION  CHARGES  PREPAID  BY  CUSTOMER  WITH  AUTHORIZED  RETURN  (RGA), 
WHICH PROVE UPON INSPECTION TO BE DEFECTIVE AND WHICH HAVE NOT BEEN MISUSED. DAMAGE OR FAILURE TO ANY 
PART DUE TO FREIGHT DAMAGE OR LACK OF REQUIRED REGULAR DOCUMENTED MAINTENANCE IS NOT COVERED UNDER 
THIS  WARRANTY.  ALL  WARRANTY  CLAIMS  MUST  BE  PERFORMED  IN  ACCORDANCE  TO  MOHAWK’S  WARRANTY  PARTS 
RETURN POLICY (CONTACT MOHAWK’S SERVICE DEPARTMENT FOR MORE INFORMATION).  
 
THIS  WARRANTY  DOES  NOT  COVER  MIS-DIAGNOSING  OF  UNIT  OR  PARTS  RETURNED  THAT  ARE  NON-DEFECTIVE.  THIS 
WARRANTY DOES NOT COVER ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES INCLUDING, BUT NOT LIMITED TO, LOST 
REVENUES  OR  BUSINESS  HARM.  THIS  EQUIPMENT  HAS  BEEN  DESIGNED  FOR  USE  IN  NORMAL  VEHICLE  MAINTENANCE 
APPLICATIONS. A SPECIFIC INDIVIDUAL WARRANTY MUST BE ISSUED FOR UNITS THAT DEVIATE FROM INTENDED USAGE, 
SUCH  AS  HIGH  CYCLE  USAGE  IN  INDUSTRIAL  APPLICATIONS,  OR  USAGE  IN  EXTREMELY  ABUSIVE  ENVIRONMENTS. 
MOHAWK RESERVES THE RIGHT TO DECLINE RESPONSIBILITY WHEN REPAIRS  OR MODIFICATIONS HAVE BEEN MADE OR 
ATTEMPTED BY OTHERS  WITHOUT  WRITTEN  AUTHORIZATION FROM MOHAWK RESOURCES LTD..  THIS WARRANTY  DOES 
NOT  COVER

 

LABOR  OR  TRANSPORTATION.  THIS  WARRANTY  DOES  NOT  COVER

 

DOWNTIME  EXPENSES  INCURRED  WHEN 

UNIT  IS  IN  REPAIR. 

THE  LIFT  MUST  BE  REGISTERED  WITHIN  30  DAYS  OF  INSTALLATION  BY  MAILING  SUPPLIED 

WARRANTY  REGISTRATION  CARD  TO  MOHAWK  AND  MUST  BE  SIGNED  BY  A  LICENSED  ELECTRICIAN

.  THE  MODEL 

NUMBER AND SERIAL NUMBER OF THE EQUIPMENT MUST BE FURNISHED WITH ALL WARRANTY CLAIMS. THIS WARRANTY 
STATEMENT  CONTAINS  THE  ENTIRE  AGREEMENT  BETWEEN  MOHAWK  RESOURCES  LTD.  AND  THE  PURCHASER  UNLESS 
OTHERWISE  SPECIFICALLY  EXPRESSED  IN  WRITING.  THIS  NON-TRANSFERABLE  WARRANTY  APPLIES  TO  THE  ORIGINAL 
PURCHASER ONLY.  
 
THIS WARRANTY DOES NOT COVER NORMAL SURFACE WEAR ITEMS, ITEMS SUBJECT TO ABRASION, OR ITEMS USED IN A 
CORROSIVE ENVIRONMENT. SOME ITEMS ON LIFT ARE SUBJECT TO NORMAL “WEAR AND TEAR” AND ARE NOT COVERED 
UNDER THIS WARRANTY. 

 

STRUCTURAL AND MECHANICAL COMPONENTS (ALL LIFTS): 

STRUCTURAL  AND MECHANICAL COMPONENTS OF THIS UNIT  ARE  GUARANTEED  FOR THE BELOW STATED  TIME FRAME, 
SPECIFIC  TO  MODEL  LISTED,  FROM  THE  DATE  OF  SHIPMENT  FROM  FACTORY,  AGAINST  DEFECTS  IN  WORKMANSHIP 
AND/OR MATERIALS WHEN LIFT IS INSTALLED AND USED ACCORDING TO SPECIFICATIONS. 
 

25-YEARS STRUCTURAL / 10 YEARS MECHANICAL

:   TWO-POST MODELS A-7, SYSTEM IA-10, LC-12, LMF-12, TP-

16, TP-18, TP-20, TP-26, TP-30. STRUCTURAL ITEMS COVERED INCLUDE LEG, CARRIAGE, SWING ARM AND 
SLIDER WELDMENTS (EXCLUDING NORMAL WEAR AREAS AS STATED ABOVE). MECHANICAL ITEMS COVERED 
INCLUDE ROLLER BEARINGS AND LIFTING CHAIN. 

5-YEAR:

   MODELS TL-7. 

3-YEAR:

   MODELS TR-19, TR-25, FL-25, TR-30, TR-33, TR-35, TR-50, TR-75, TR-110, TR-120, MP-SERIES LIFTS. 

2-YEAR:

   MODELS PARALLELOGRAM SERIES LIFTS.

 

1-YEAR:

   MODELS TD-1000, TD-2000, CT-1000, USL-6000. 

 

POWER UNIT (ALL LIFTS): 

ALL POWER UNIT COMPONENTS (MOTOR, PUMP AND RESERVOIR) ARE GUARANTEED FOR TWO YEARS FOR PARTS, 
FROM THE DATE OF SHIPMENT FROM FACTORY, AGAINST DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN THE 
LIFT IS INSTALLED, WIRED BY A LICENSED ELECTRICIAN AND USED ACCORDING TO SPECIFICATIONS. 
 

ELECTRICAL COMPONENTS (ALL LIFTS): 

ALL ELECTRICAL COMPONENTS (EXCLUDING MOTOR) ARE GUARANTEED FOR ONE YEAR FOR PARTS, FROM THE DATE 
OF SHIPMENT FROM FACTORY, AGAINST DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN THE LIFT IS 
INSTALLED AND USED ACCORDING TO SPECIFICATIONS. SEE WARRANTY EXCEPTIONS SECTION FOR BATTERIES. 
 

PNEUMATIC-AIR COMPONENTS (ALL LIFTS): 

ALL PNEUMATIC (AIR) COMPONENTS (I.E. AIR CYLINDERS AND POPPET AIR VALVES) ARE GUARANTEED FOR ONE YEAR 
FOR PARTS, FROM THE DATE OF SHIPMENT FROM FACTORY, AGAINST DEFECTS IN WORKMANSHIP AND/OR 
MATERIALS WHEN THE LIFT IS INSTALLED AND USED ACCORDING TO SPECIFICATIONS. COMPONENTS IN A PNEUMATIC 
SYSTEM THAT ARE NOT PROPERLY REGULATED, LUBRICATED AND CONDITIONED WITH AN AIR DRYING SYSTEM ARE 
NOT COVERED UNDER WARRANTY. 
 

HYDRAULIC COMPONENTS (ALL LIFTS): 

EXCLUDING CYLINDERS AND PUMPS (COVERED IN OTHER SECTIONS), ALL HYDRAULIC COMPONENTS (I.E. VALVES AND 
FITTINGS) ARE GUARANTEED FOR ONE YEAR FOR PARTS, FROM THE DATE OF SHIPMENT FROM FACTORY, AGAINST  

Содержание A-7











































































Отзывы: