MOGlabs ARF021 Скачать руководство пользователя страница 122

Страница: 122 / 134

112

Appendix C. Command language

ENABLE

PID,ENABLE,ch,mode

Enables

the

PID

controller

for

the

given

channel

the

specified

mode

, which is one of

FREQ

AMPL

PHAS

DISABLE

PID,DISABLE,ch

Disables the

PID

controller for the given channel.

RATE

PID,RATE,ch[,rate]

Sets the

rate

at which the analogue control signal is digitised.

rate

is a floating point value in MHz, which is rounded to the nearest

valid rate.

Valid rates are 15.6 MHz, 7.81 MHz, 3.91 MHz and 1.95 MHz.

STATUS

PID,STATUS,ch

Reports the current status of the

PID

controller and whether satura-

tion occurred.

The saturation flag is reset by this query.

AVERAGE

PID,AVERAGE,ch[,on/off]

Enables/disables averaging of the input control signal.

The digiti-

sers operate at much higher rates than the

PID

sampling rate.

With

averaging on, the extra measurements contribute to an average sig-

nal

which

reset

the

sampling

rate.

averaging

off,

the

additional measurements are discarded.

DCBLOCK

PID,DCBLOCK,ch[,on/off]

Enables/disables

block

, which allows the error to be driven to a

non-zero

value.

block

is equivalent to a series capacitor in

the input control signal, prior to the

PID

controller.

INVERT

PID,INVERT,ch[,on/off]

Inverts the controller action for the given channel.

GAIN

PID,GAIN,ch,name[,value]

Sets the

PID

gain constant for

name

, which is one of

(proportional),

(integral) or

(derivative), as described in

6.2.

value

is a floating

point number in the range [0,1).

Содержание ARF021







































































































































Результаты поиска

Содержание ARF021

Отзывы:

Бренды по названию

Популярные бренды

MOGlabs ARF021, Руководство пользователя

Результаты поиска

Содержание ARF021

Отзывы:

Бренды по названию

Популярные бренды