Modena BZ 1005 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 33

background image

30

The  information  shown  below  aims  to  help  with  the  identification  and  correction  of  any  anomalies  and  malfunction
whuch  could  occur  during  operation.  Some  of  these  probles  can  be  resolved  by  the  user.  For  the  others,  the
precise  skill is required  and  must only be carried  out  by authorized  technician.

Problem

Possible Causes

Recommended Action

The refrigerator unit does
not start

No voltage

Check the power supply cable

Check fuses

Check the correct connection of the
appliance

Other causes

If the problem persists, contact
MODENA Call Center

The  refrigerator  unit
functions  continuously,
cooling  insufficiently

Room is too hot

Air the environment

Dirty condenser

Clean the condenser

Insufficient door sealing Check the gaskets

Insufficient quantity of
refrigerant gas

Contact MODENA Call Center

Condenser fan
at a standstill

Contact MODENA Call Center

Evaporator fan
standstill

Contact MODENA Call Center

The refrigerator unit does
not stop

Probe faulty

Contact MODENA Call Center

Circuit board fault

Contact MODENA Call Center

Presence of ice inside the
evaporator

Carry out a defrosting cycle possibly with the
door open

If the problem persists, contact
MODENA Call Center

Appliance noise

Persistent vibrations

Check there is no contact between the
appliance and other objects inside or outside

This appliance is marked in compliance with the 2002/96/EC European Directive.
WASTE ELECTRICAL AND ELECTRIC EQUIPMENT (WEEE).

By  assuring  that  this  product  is  disposed  of  correctly,  the  user  contributes  to preventing the potential
negative  consequences  on the  environment  and  health.

The  symbol  found  on  the  product  or  on  the  accompanying  documentation  indicates  that  this  product
must  not  be  treated  as  domestic  waste  but  must  be  taken  to  suitable  collection  points  for  the
recycling of  electric and  electronic  appliances.

Dispose  of  it following  local regulations  regarding  waste disposal.
For  further  information  regarding  the  treatment,  recovery  and  recy cling  of  this  product,  contact  the  relevant  local
office,  the  domestic waste collection  service  or  the shop  where  the product  was   purchased.

Part 6: Troubleshooting

Part 7: Disposal

«
...
28
29
30
31
32
...
»

Содержание BZ 1005


































Отзывы:

Нет отзывов

Похожие инструкции для BZ 1005

Бренд: YAAHKIEH Страницы: 16

Бренд: S&A Страницы: 13

Бренд: S&A Страницы: 15

INNOVA DHADC Series

Бренд: Lennox Страницы: 56

Бренд: Yard-Man Страницы: 20

Бренд: York Страницы: 104

Бренд: Nakayama Страницы: 40

VERSA 20015 SERIES

Бренд: EarthQuake Страницы: 36

Бренд: Hansa Страницы: 29

Бренд: Lava Страницы: 76

Бренд: Texas Страницы: 60

Бренд: Lauda Страницы: 112

Бренд: Angelo Po Страницы: 48

Бренд: Nac Страницы: 65

Бренд: Toyama Страницы: 60

Бренд: Racing Страницы: 23

Бренд: Dakin Страницы: 19

Бренд: MADER Страницы: 101

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды