Modena BZ 1005 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 33

background image

14



Light

(4): push the LIGHT (4) button to switch the light on and off. The status of the light is

monitored by the yellow LED upper the button.



AUX

(8): push the AUX (8) button to switch the auxiliary on and off. The status of the auxiliary

relay is monitored by the yellow LED upper the button.



Printer

/ H (7): to enabled / disable the printer, push the PRINTER button when the buttonboard

is connected to the controller.



Printer configuration menu

Push the PRINTER (7) button for few seconds to enter the printer configuration menu. The

itP

, label is

displayed, use the ARROW buttons to browse the parameters

To modify:

push the

SET

button and then the ARROW buttons.

To confirm

: push the

SET

button

To exit the Printer menu

: Push together SET + UP buttons or wait 5 sec



How to start a manual defrost

1. Assure that none cycle is active or the hold mode is running.
2. Hold press the

UP

button fro few seconds.

NOTE

: The defrost will not be done if the temperature detected by the evaporator probe is higher than

EdF (stop defrost temperature) parameter.



Other function of button board

«
...
12
13
14
15
16
...
»

Содержание BZ 1005


































Отзывы:

Нет отзывов

Похожие инструкции для BZ 1005

Бренд: York Страницы: 176

Бренд: U-Line Страницы: 67

Бренд: Poulan Pro Страницы: 40

Бренд: Pattfield Ergo Tools Страницы: 68

Бренд: Barazza Страницы: 32

CenTraVac CDHF Series

Бренд: Trane Страницы: 104

Бренд: Elemental Solutions Страницы: 4

DELTA II 9100 Series

Бренд: lancer Страницы: 28

Бренд: Titan Pro Страницы: 22

Бренд: Kaysun Страницы: 60

Бренд: Cavecool Страницы: 27

Бренд: Agrisem Страницы: 54

Бренд: Chapman Страницы: 11

FANTOM 1050 PRO

Бренд: Farmet Страницы: 59

Бренд: Perlick Страницы: 12

Бренд: Häfele Страницы: 11

Бренд: KDF Страницы: 2

Бренд: Quantech Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды