Modeltech Magic Extra 300L Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 40

Modeltech Magic Extra 300L Скачать руководство пользователя страница 7

7

Need help or have any questions? Call us at 1-714-963-0329 or send us an Email at [email protected]

Global stocks a complete line of replacement parts for your Modeltech Magic Extra 300L ARF. Listed below are the
replacement parts that are available along with their respective part numbers for easy ordering convenience. We suggest
ordering directly from your local dealer. If your dealer does not stock Modeltech products, you can order directly from us at
the address shown below:

SECTION 5: REPLACEMENT PARTS

Global Services

18480 Bandilier Circle

Fountain Valley CA 92708

Phone: (714) 963-0329 Fax: (714) 964-6236

On the Web

http://globalservices.globalhobby.com

The covering material used on the Magic Extra 300L ARF is real iron-on heat-shrink covering material, not cheap
"shelf paper." Because of this, it is possible with heat and humidity changes that the covering on your airplane may
wrinkle or sag. This trait is inherent in all types of heat-shrink material. To remove any wrinkles that might be visible
you will need to purchase, or borrow from a fellow modeler, a heat iron. If you need to purchase one, the

Global Heat

Sealing Iron # 360900

is recommended.

Follow this simple procedure to remove the wrinkles:

❑

Plug in and turn on the sealing iron to the medium-high temperature setting. Allow the iron to heat up for approximately

5 - 7 minutes.

❑

After the iron has reached temperature, lightly apply the iron to the wrinkled section of the covering. Move the iron

slowly over the wrinkled section until the covering tightens and the wrinkles disappear. You will notice that the color of the
covering will darken when it is heated. When the covering cools back down, it will return to its normal color.

☞

If the color layer smears from any of the seams the temperature of the iron is too hot. Turn the temperature dial down

and wait about 5 minutes for the iron to adjust to the lower temperature. You can remove any excess color streaks using
a paper towel soaked with a small quantity of Acetone.

WARNING

We do not suggest storing your airplane in an extremely hot environment (like the back of your car in direct
sunlight) for any length of time. The extreme heat could cause the covering material to wrinkle or sag and
possibly damage the clear canopy, and the fragile components of the radio system.

SECTION 6: A NOTE ABOUT COVERING

Modeltech Magic Extra 300L - Complete -

123739

Instruction Manual

-

170800

Wing Set

-

170801

Fuselage Set

-

170802

Stabilizer Set

-

170803

Clear Molded Canopy

-

170804

Blow-Molded Wheel Pants

-

170805

Hardware Set

-

170806

Fuel Tank Assembly

-

170807

Aluminum Landing Gear Bracket

-

170808

Decal Sheet

-

170809

Tail Wheel Assembly

-

170810

Spinner Assembly

-

170811

Engine Mount Assembly

-

170812

Belly Pan

-

170813

«
...
5
6
7
8
9
...
»

Содержание Magic Extra 300L









































Отзывы:

Нет отзывов