manualshive.com logo in svg

Modeltech Magic Extra 300L, Инструкции по окончательной сборке, Страница: 4 / 40

Поделиться
Скачать
Modeltech Magic Extra 300L Скачать руководство пользователя страница 4

4

Visit our website at http://modeltech.globalhobby.com or for Customer Service at http://globalservices.globalhobby.com

Here's a List of What We Used to Finish Our Magic Extra 300L:

This section describes our recommendations to help you in deciding which types of accessories to purchase for your
new Modeltech Magic Extra 300L ARF.  These suggestions are not set in stone, but they should provide you with a good
starting point.

SECTION 1:  OUR RECOMMENDATIONS

What Engine Should I Use?

The Magic Extra will accept a wide variety of engines, so which engine you choose really depends on how you want to fly
the airplane.  For general sport flying, a .40 to .53 2-stroke engine with a 10 x 6 propeller (for .40) or an 11 x 6 propeller
(for .46) would be perfect.  If you wanted to use a 4-stroke engine, a .61 4-stroke with a 13 x 5 propeller would be a good
choice, too.

For 3D style aerobatics, you want to focus more on using lightweight, but powerful, engines with large diameter, low pitch
propellers.  There are many engines that fit this criteria, so it really depends on how much money you want to spend.  For
good 3D performance and a low price, a good sport .46 size engine with an APC 12.25 x 3.75 propeller would be perfect.

What Radio System & Servos Should I Use?

For typical sport-flying and general aerobatics, a standard 4 channel radio system will be more than adequate.  Since the
ailerons use separate aileron servos, you will need to use a servo Y-harness to join them.  The Magic Extra is not a big,
heavy airplane, so it's not necessary to use high-torque servos.  Five standard size servos will work fine.

For 3D aerobatics, a four or more channel computer radio with mixing capabilities will be required.  Since there are two
separate aileron servos used, they can be plugged separately into the receiver, allowing you the capability of flaperon or
spoileron mixing and differential.  For 3D aerobatics, we still recommend standard size servos, but we strongly suggest
using ball bearing servos on the control surfaces.

What Else Do I Need?

The Magic Extra includes all the hardware you'll need to finish the airplane.  You will need some basic building materials,
such as adhesives, protective foam rubber for your radio gear, and fuel tubing.  We've provided a list below of the items we
used on the airplane shown in this instruction manual.

QTY. 1

210756

Magnum XLS .46 2-Stroke Engine

QTY. 1

608684

APC 12.25 x 3.75 Composite Propeller

QTY. 1

115493

Thunderbolt R/C Long Glow Plug

QTY. 1

115923

Global XX Silicon Fuel Tubing

QTY. 1

868638

Dubro 1/4" Protective Foam Rubber

QTY. 4

444110

Cirrus CS-71 BB Standard Servos

QTY. 1

444107

Cirrus CS-71 Standard Servo

QTY. 1

444728

Cirrus Servo Y-Harness (optional)

IMPORTANT

The part numbers listed for the Cirrus servos and the Cirrus Y-Harness are compatible with Hitec and JR radio control systems.  These
items are also available with connectors that are compatible with Futaba and Airtronics radio control systems.

Содержание Magic Extra 300L









































Отзывы:

Нет отзывов