manualshive.com logo in svg

Modeltech Magic Extra 300L, Инструкции по окончательной сборке, Страница: 31 / 40

Поделиться
Скачать
Modeltech Magic Extra 300L Скачать руководство пользователя страница 31

31

Need help or have any questions?  Call us at 1-714-963-0329 or send us an Email at [email protected]

❑

Thread the clevis onto the pushrod wire and snap it into

the outermost hole from the base of the control horn.

❑

Repeat the previous steps to install the second aileron pushrod assembly on the opposite wing panel.

❑

Pacer Formula 560 Canopy Glue

❑

# 1 Phillips Head Screwdriver

❑

Promax Canopy Scissors

❑

220 Grit Sandpaper w/Sanding Block

❑

Masking Tape

YOU'LL NEED THE FOLLOWING PARTS FROM THE KIT:

❑

(1) Clear Molded Canopy

❑

(1) Spinner Assembly w/Wood Screws

SECTION 20:  FINAL ASSEMBLY

❑

(2) 2mm x 10mm Wood Screws

❑

(1) 2mm x 12mm Wood Screw

YOU'LL NEED THE FOLLOWING TOOLS AND SUPPLIES:

❑

Electric Drill

❑

5/64" Drill Bit

❑

Ernst Airplane Stand

❑

Ruler

❑

Pencil

Step 1:  Installing the Clear Canopy

❑

Using a pair of scissors, carefully cut out the canopy along the molded scribe line.

❑

Using 220 grit sandpaper with a sanding block, carefully sand the edges of the canopy smooth and straight.

☞

Be careful not to scratch the surface of the canopy when sanding its edges.

❑

Set the canopy onto the fuselage and align it.  The canopy

should be centered over the middle of the fuselage and the
front edge of the canopy should be 1/16" behind the back
edge of the hatch cover.

❑

When satisfied with the fit, remove the canopy and carefully apply a thin bead of Pacer Formula 560 Canopy Glue

around the inside edges of the canopy.

❑

Set the canopy back into place and realign it.  Use pieces of masking tape to hold the edges of the canopy firmly in

place and remove any excess adhesive using a paper towel soaked with 

water.

Содержание Magic Extra 300L









































Отзывы:

Нет отзывов