manualshive.com logo in svg

Modeltech Magic Extra 300L, Инструкции по окончательной сборке, Страница: 27 / 40

Поделиться
Скачать
Modeltech Magic Extra 300L Скачать руководство пользователя страница 27

27

Need help or have any questions?  Call us at 1-714-963-0329 or send us an Email at [email protected]

❑

Partially thread the 3mm x 8mm set screws into the wheel collars.  Slide the wheel collars onto the elevator pushrod

wire and up against the snap keeper.

❑

Make a shallow bend 1-1/2" from the plain end of the

13-1/2" long pushrod wire and slide the pushrod wire through
the wheel collars as shown.  The bend should be deep enough
to separate the pushrod wires by 1/2".

❑

Adjust the pushrod wire so both pushrod ends are even

with each other.  When satisfied with the alignment, tighten
the set screws in both wheel collars.

☞

When tightening the set screws, make sure both pushrods

stay flat and don't twist up.

❑

Carefully slide the pushrod wires into the preinstalled

pushrod housings in the rear bulkhead - the two that are higher
up in the fuselage and are at the same height as the servo.

❑

Install the servo horn, making sure it's centered and

pointing toward the middle of the fuselage as shown.

❑

Install the servo horn retaining screw to secure the servo

horn to the servo.

❑

Using a modeling knife, cut away and remove the covering material from over the elevator pushrod exit holes in each

side of the fuselage.  They are located 5-1/4" in front of the rudder hinge line and 1-7/8" above the bottom of the fuselage.

❑

Connect your radio system and plug the elevator servo (rear-most servo) into the receiver.  Double-check that the

elevator trim lever on your transmitter is centered.

Step 2:  Installing the Elevator Pushrod Assembly

Step 3:  Installing the Control Horns & Clevises

❑

Use a couple of pieces of masking tape to hold the elevator halves centered.

❑

Position one nylon control horn onto the bottom of one

elevator half, aligning the centerline of the control horn with
the pushrod wire.  The centerline of the control horn should
be approximately 7/8" out from the side of the fuselage.

❑

Angle the control horn about 1/16" toward the fuselage

side so it will line up better with the pushrod wire and adjust the
control horn so that the clevis attachment holes are directly
over the hinge line.

❑

Mark the positions of the control horn mounting screws, then remove the control horn and set it aside.

❑

Drill the holes through the elevator for the mounting screws using a 5/64" diameter drill bit.

Содержание Magic Extra 300L









































Отзывы:

Нет отзывов