Modeltech Magic Extra 300L Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 40

Modeltech Magic Extra 300L Скачать руководство пользователя страница 26

26

Visit our website at http://modeltech.globalhobby.com or for Customer Service at http://globalservices.globalhobby.com

❑

Position the throttle control stick and the throttle trim lever on your transmitter at their lowest positions. Slide the

adjustable servo connector/servo horn assembly over the plain end of the throttle pushrod wire.

❑

After making sure that the carburetor is in the fully closed

position, angle the servo horn back about 45º from center
and attach it to the servo output shaft. The servo connector
should be facing the side of the fuselage.

❑

While holding the carburetor barrel fully closed, install

and tighten the set screw in the top of the adjustable servo
connector.

❑

Use wire cutters to cut away and remove the excess

pushrod wire.

❑

Install and tighten the servo horn retaining screw to hold the servo horn securely to the servo.

❑

Kwik Bond Thin C/A

❑

# 1 Phillips Head Screwdriver

❑

Needle Nose Pliers

❑

Excel Modeling Knife

❑

Electric Drill

YOU'LL NEED THE FOLLOWING PARTS FROM THE KIT:

❑

(1) 14-1/2" Threaded Wire w/90º Bend

❑

(1) 13-1/2" Threaded Wire

❑

(2) Nylon Control Horns w/Backplates

❑

(4) 2mm x 12mm Machine Screws

SECTION 17: ELEVATOR CONTROL SYSTEM INSTALLATION

❑

(2) Nylon Clevises

❑

(1) Nylon 90º Snap Keeper

❑

(2) Wheel Collars w/3mm x 8mm Set Screws

YOU'LL NEED THE FOLLOWING TOOLS AND SUPPLIES:

❑

5/64" Drill Bit

❑

Ernst Airplane Stand

❑

Ruler

❑

Pencil

❑

Masking Tape

Step 1: Assembling the Elevator Pushrod

❑

Using a modeling knife, cut away all but one arm from a large "4-point" servo horn.

❑

Enlarge the

fourth hole

out from the center of the servo arm using a 5/64" drill bit.

❑

Install the 90º bend in the 14-1/2" long elevator pushrod

wire into the hole that you just enlarged, using the snap keeper
provided. When installing the snap keeper, make sure it
"snaps" firmly into place over the pushrod wire.

☞

The pushrod wire should be on top of the servo arm

as shown.

«
...
24
25
26
27
28
...
»

Содержание Magic Extra 300L









































Отзывы:

Нет отзывов