8
LSI_K_np_en 1206_mmm_V2.08_B2V
Instructions for use
The programs in the memory will be recorded
over (erased). make sure the chip card is in
the card reader. Press
STArT/STOp
to open
the programme download service. The display
shows: „MMM CCard → P1 ÷ 6”,
Press
X/W
to record. The transmission is
confirmed by the read out „Done“ on LCD. Press
STArT/STOp
again to enter another service. If
the read out on the LCD is „Bad MMM CCard“,
check the chip card and repeat the procedure.
ATTENTiON!
The original chip card delivered by the
manufacturer should be used only. Cards whose
type ends with the figure 1024 (AT24C1024) may
only be used. Older cards ending with the figure
16 may not be used.
4.1.4
SERVICE
03
-
SET
THE
REAL
TIME
AND
DATE
Pressing
STArT/STOp
you enter the service.
Set the real time and date by pressing buttons
◄► and ▲. Enter the date format setting by
shifting the cursor behind the display edge,
using the buttons ◄►. The date format is
selected by pressing ▲ while the cursor is
on the position 7. The possible formats are
(in Czech): rrrr-mm-DD, rrrr-DD-mm,
mm-DD-rrrr, and DD-mm-rrrr. The default
format is rrrr-mm-DD. (In other languages:
yyyy-mm-DD, JJJJ-mm-TT, or aaaa-mm-JJ).
The data delimiter is selected by pressing ▲
while the cursor is on the position 6. The key ◄
takes you back to the time setting.
To quit the service press
STArT/STOp
again.
4.1.5
SERVICE
04
-
SET
INTERVAL
ON
PRINTER
/
COMMUNICATION
INTERFACE
To print the protocols the units of thermal
technology may be provided (optional) with a
printer, which is connected by a cable to the
printer interface – see chapter
4.8 - printing the
protocol
by
STArT/STOp
and set the interval:
Pressing ▲ select one of the following choices:
- printer oFF
- switched over to PC (application of SW
WarmComm – data are sent to PC)
- interval 10 s
- interval 01 min
- interval 01 hr.
By pressing ◄ move the cursor to the position
10/01 seconds, minutes or hours. By pressing
▲ you can change the printer interval within the
following range:
-10 to 50 s (step 10 s)
- 01 to 59 min (step 1 min)
- 01 to 12 h (step 1 h).
one unit only is active, either seconds, or
minutes, or hours.
By further move of the cursor to the display edge,
you enter printer selection. Select the printer type
by means of ▲
Printer=1 ... Citizen
Printer=2 ... Thermal printer DPT 6333-V.24
To quit the service press
STArT/STOp
again.
4.1.6
SERVICE
05
-
SELECT
LANGUAGE
Pressing
STArT/STOp
you enter the service.
To select the language use button ▲ To quit the
service press
STArT/STOp
again.
4.1.7
SERVICE
06 –
SETTING
THE
SWITCHING
TIMES
OF
INNER
SOCKET
(
OPTIONAL
)
AND
THE
FAN
RUN
AFTER
THE
PROGRAMME
TERMINATION
A) Switching times setting
ATTENTiON!
Using this service you can set the time of
periodical switching on and off of the inner
socket.
open the service by pressing
STArT/STOp
. The
bottom line of LCD states:
“on: XXPP off: YYQQ”,
where XXPP is the time for which the socket is
switched on for one part of the period (00 – 99),
YYQQ is the time when it is switched off (00 –
99).
PP is the abbreviation of time unit (minutes or
hours) for switching on, QQ for switching off.
The following applies: XXPP + YYQQ = whole
period.
Use ◄ and ► to move the cursor, use ▲ to
change the numbers of time units or units.
If XX = 00, then the socket never switches
on, if XX ≠ 00 and YY = 00, then the socket is
permanently switched on after the start up to
termination.
B) Setting the fan run after the programme
termination
Leave the “inner socket” setting by means of
◄► and by pressing ▲, set:
a) “Prog” – the fan runs only during the P1-P6
run;
b) „T50C“-„T250“ – the fan runs even after
program termination, up to temperature
decrease below pre-set value (it is possible
