ML System Two D Series Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 68

ML System Two D Series Скачать руководство пользователя страница 63

System Two LED Installation and Service Manual (1003385 Rev. C)

Page 63

Section 6

Dismantling and re-mounting the securing segment

Figure 41: Checking the securing segment

The light head and monitor cradle are kept in its
position in the Spring Arm by 2 securing segments.
If both securing segments are dismantled
simultaneously from the Spring Arm, there is a risk
of the light head or monitor cradle dropping out of
the Spring Arm and causing severe injury;



Dismantle the securing segments one after the

other.

Dismantling the first securing segment

1. Rotate the segment securing device

①

approximately 90° to the right, route it slightly down-
wards and then remove the first securing segment

②

.



To do this, cover the second securing segment on

the opposite side with your hand in order to prevent
it from dropping out of the Spring Arm.

2. Route the segment securing device

①

back

upwards.

3. Check whether the securing segment

②

achieves a

minimum thickness of

0.07” (1.8mm) and a minimum

length of

0.33” (8.3mm); otherwise, replace the

securing segment.



Use a caliper gauge for measurement.



Replace the securing segment

②

if the specified

dimensions are not achieved.

Mounting the first securing segment

4. Lubricate the securing segment

②

with white

grease.

5. Route the segment securing device

①

slightly

downwards.



To do this, cover the second securing segment on

the opposite side with your hand in order to prevent
it from dropping out of the Spring Arm.

6. Lubricate the pivot of the Light Head/Yoke Assembly

or Monitor Cradle with white grease through the
fitting aperture of the securing segment

②

.

7. Place the securing segment

②

and route the

segment securing device

①

towards the top and

then rotate it approximately 90° to the left.



The cutout

③

in the segment securing device

①

must protrude over the optional brake screw or
brake screw hole

④

.

8. Check that the securing segment

②

is securely in

place;



The Light Head or Monitor must rotate freely.

Checking the second securing segment

9. Dismantle and check the second securing segment.
10. Re-mount the second securing segment.

Adjusting the vertical lift and the optional brake

11. Adjust the vertical lift of the Spring Arm and the

optional brake described previously.



Mount the cover panels to the Spring Arm.

«
...
61
62
63
64
65
...
»

Содержание System Two D Series





































































Отзывы:

Нет отзывов