manualshive.com logo in svg

ML System Two D Series, Инструкция по установке и обслуживанию, Страница: 44 / 68

Поделиться
Скачать
ML System Two D Series Скачать руководство пользователя страница 44

System Two LED Installation and Service Manual (1003385 Rev. C)

 

Page 44

 

Section 5 

Adjusting the Brakes for the Spring Arm (cont) 

 

 

 

Figure 23: Mounting the socket covers and decorative 
caps to the Extension Arms 

 

 

 

 

 

 

The Figure shows a simplified illustration with only 
the Extension Arm [4] without Spring Arm. 

Mounting the socket covers to the Extension Arm 

1.  Screw the left-hand socket cover with optional cover 

plate 

② 

onto the Extension Arm [4] using 2 cross 

recessed head screws 

①

.

 

2.  Place the right-hand cover panel with optional cover 

plate onto the left-hand socket cover 

②

 such that all 

the locking pins 

③

 engage with each other and 

screw it onto the Extension Arm [4] using 2 cross 
recessed head screws 

①

. 

3.  Check that the socket cover with optional cover 

plates is securely in place; 

  The socket covers with optional cover plates 

② 

must tightly engage with each other without gaps 
and be tightened with 2 cross recessed head screws 

①

. 

 

Mounting the decorative caps 

*** Notice *** 

To prevent damage to the decorative caps

; 

  The mounting steps described below must be 

executed in the correct order: 

1.  Attach the locking mechanisms 

⑥

 of the decorative 

caps 

④

 into the 2 fittings 

⑤ 

on the socket covers 

②

. 

2.  Fold the decorative caps 

④

 towards the Extension 

Arm [4] and insert the straps 

⑧ 

into the cutout 

⑦ 

on the socket covers 

②

. 

3.  Check that the decorative caps 

④

 are securely in 

place; 

  The decorative caps 

④

 must securely engage in the 

socket covers 

② 

without gaps. 

 

 
 

 

Содержание System Two D Series





































































Отзывы:

Нет отзывов