manualshive.com logo in svg

ML System Two D Series, Инструкция по установке и обслуживанию, Страница: 5 / 68

Поделиться
Скачать
ML System Two D Series Скачать руководство пользователя страница 5

System Two LED Installation and Service Manual (1003385 Rev. C)

 

Page 5

 

Thank you 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Visit us on the Internet 

E-mail Address 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
Thank you for purchasing this Medical Illumination product. 
Please read these Operating Instructions very carefully, abide 
by the safety notices and observe all operating and cleaning 
requirements. 

These Operating Instructions apply to; 

System Two LED Surgical Light and Central Axis S1 

System Two LED Surgical Light and Central Axis S2 

System Two LED Surgical Light and Central Axis S3 

Please do not hesitate to contact our Customer Service 
team 

if you have any questions about the appliance and its 
installation, and also in service or warranty cases.

 

Manufacturer and distributor 

Medical Illumination International 
547 Library St 
San Fernando, CA 91340 
(818) 838-3025 
 
www.medillum.com 
[email protected] 
 
 

Supplier’s address 

 
 
 
 
 
 
 
 
 
Space for supplier’s stamp or label 
 
 
 
 

 
 

 

Содержание System Two D Series





































































Отзывы:

Нет отзывов