manualshive.com logo in svg

ML System Two D Series, Инструкция по установке и обслуживанию, Страница: 30 / 68

Поделиться
Скачать
ML System Two D Series Скачать руководство пользователя страница 30

System Two LED Installation and Service Manual (1003385 Rev. C)

 

Page 30

 

Section 4 

Mounting the L17 and LCH Spring Arm 

 

 

Figure 8: Mounting the L17 and LCH Spring Arms

 

 
 

Two people are required to mount the Spring Arm. 
An equipment lift is highly recommended to avoid 
injury in lifting the Spring Arm into place. 

1.  Pull the 2 latch pins 

① 

upwards and route the 2 

securing segments 

② 

out of the Extension Arm 

until they snap into place 

⑤

. 

2.  Insert the Spring Arm pivot 

④

 straight into the 

Extension Arm up to the end stop without twisting. 

 

The plug couplings mounted inside the Extension 
Arm and Spring Arm are connected during this 
installation step. 

3.  Insert 2 securing segments 

② 

into the Extension 

Arm up to the end stop such that they snap into 
place: 

 

The 2 securing segments 

② 

must protrude into the 

groove 

③

 on the Spring Arm pivot 

④

 

 

The 2 spring-actuated latch pins 

① 

audibly click 

into place. 

*** Risk of the Light Head dropping *** 

If the 2 securing segments 

② 

are not properly 

mounted, there is a risk of the Spring Arm with the Light 
Head dropping and causing serious injury. Check the 2 
securing segments 

② 

are securely in place: 

 

The Spring Arm must be inserted into the 
Extension Arm up to the end stop. 

 

The 2 securing segments 

② 

must be inserted into 

the Extension up to the end stop such that they 
protrude into the groove 

③

 on the Spring Arm pivot 

④

. 

 

The 2 latch pins 

① 

must audibly snap into place 

and be on the same height after the installation. 

 

 

 

Содержание System Two D Series





































































Отзывы:

Нет отзывов