manualshive.com logo in svg

ML System Two D Series, Инструкция по установке и обслуживанию, Страница: 48 / 68

Поделиться
Скачать
ML System Two D Series Скачать руководство пользователя страница 48

System Two LED Installation and Service Manual (1003385 Rev. C)

 

Page 48

 

Section 5 

Adjusting the Spring Tension 

 

The Spring Arm [5] is equipped with a spring which 
compensates the weight of the Light Head or the 
weight of a monitor. 

Adjust the spring tension such that the Spring Arm with 
remains stable in any set position. 

Follow the safety instructions on Page 56. 

Disengaging the cover plate 

1.  Insert a suitable slotted screwdriver into the 

mounting aperture 

④

 

2.  Slightly push the slotted screwdriver upwards and 

route the snap-in hook 

①

 out of the cover. 

3.  Push the slotted screwdriver with the cover plate 

③

 

backwards. 

Setting 

  Use an Allen key (size 5). 

4.  Gently route any electric cables 

⑥

 towards the side 

and insert the Allen key into the adjustment aperture 

⑤

. 

  Route the Spring Arm approxi5° to +10° 

upwards in order to relieve the adjustment screw. If 
the Spring Arm moves down, the spring tension is 
too low 

  Turn the Allen key to the left (counter-clockwise) as 

illustrated in the Figure. If the Spring Arm moves up, 
the spring tension is too high 

  Turn the Allen key to the right (clockwise) as 

illustrated in the Figure. 

5.  Perform a function test. 

Engaging the cover plate 

6.  Push the cover plate 

③

 forward and manually insert 

the 2 latches 

② 

into the cover panel. 

7.  Insert the slotted screwdriver into the hole 

④

, push 

the cover plate 

③

 slightly upwards and route the 

snap-in hook 

①

 into the cover panel. 

8.  Move the Spring Arm up & down and check that the 

cover plate 

③

 is securely in place. 

  The snap-in hook 

①

 must sit in the cover panel. 

  The cover plates must slide in the lateral guides 

without being trapped. 

 

 

Figure 26: Adjusting the spring tension 

Содержание System Two D Series





































































Отзывы:

Нет отзывов