manualshive.com logo in svg

MKS PR 4000 F, Инструкция по эксплуатации

Поделиться
Скачать
MKS PR 4000 F Скачать руководство пользователя страница 41

PR4000F

Chapter 4:  Operation

33

4.4    Control

For routine operation, e.g. flow readout and setpoint settings, after the setup has been finished
there will be 1 to three windows, depending on the configuration choosen, plus two displays for
control parameters and status information.

Display for measurement values and setpoints

Example for setting of display 1:

Example for display 2:

The windows above show the format which would come up when following the examples described
in the section 

Setup

.

To ease operation the setpoints SP1 or SP2 can be set here. It is not necessary to enter the setup.

Messages:

OVERFLW

The measurement signal e11 V. As an example this would be the
case when an absolute pressure transducer with a low full scale range, e.g.
1 mbar, is connected to this channel and it’s port is open to atmosphere.

UNDRFLW

The measurement signal exceeds -11 V.

CH1               05.160 mbar

CH2               17.690

 

sccm

FL2                17.690 SCCM

SP2                20.000 SCCM

Содержание PR 4000 F






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды