manualshive.com logo in svg

MKS PR 4000 F, Инструкция по эксплуатации

Поделиться
Скачать
MKS PR 4000 F Скачать руководство пользователя страница 20

Chapter 2:  Installation

PR4000F

12

Line Power and Fuses

The two wire line power connection is protected by two fuses. Before connecting the unit to the AC
power source you must check that the voltage selector switch is set to the correct mains voltage.
Refer to the following table in case that the line fuses must be changed or replaced respectively.
Voltage selector, fuse holder and line cord plug are located at the rear panel (see figure 3).

Voltage Selector Switch

Version

Fuse Type

230 VAC

±15 V; 0,8 A

T315mA

230 VAC

±15 V; 1,5 A

T500mA

230 VAC

+24 V; 1 A

T315mA

115 VAC

±15 V; 0,8 A

T630mA

115 VAC

±15 V; 1,5 A

T1A

115 VAC

+24 V; 1 A

T630mA

Table 3:  Fuse Information

The version of your PR4000F is derived from the informations on the serial label.

Caution

Check to make sure the voltage setting is correct for your local
electrical source.

Check to make sure the fuse type is appropriate for your voltage
setting.

Protective Grounding

Connect the power cord PR4000F only into a grounded outlet.

2.5    Switching on the unit

After all connections to the peripheral instruments, e.g. pressure transducer, mass flow controller
etc. are properly done the unit can be switched on. Refer to the instructions for the peripheral units
for proper installation, connection, set up and warm up.

The elements on the front and rear panel and their functions are explained in the following chapter.

Содержание PR 4000 F






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды