MK Diamond Products HD-101R Pro24 JCS Скачать руководство пользователя страница 29

Страница: 29 / 64

(A)

Loosen Cutting Head

Adjusting Knob.

(B)

Set cutting depth approximately

1/4 to 1/2 inch below the

surface of the Movable

Cutting Table.

(C)

Tighten the Adjusting Knob.

(A)

Position the Adjustable Cutting

Guide to desired cut length.

(B)

Tighten the retaining

thumbscrew.

(C)

Place the tile against the

Ruler/Stop and Cutting Guide.

Turn the motor ON.

(D)

Verify proper cooling flow on

both sides of the blade (See

Maintenance Section to

increase/decrease flow).

(E)

Perform the cut. Turn the motor

OFF when work is complete.

CaUTion

HD-101R Pro24

aDJUSTMenT

When loosing the Cutting Head Adjusting Knob, the Cutting Head will pivot

down unless held.

CaUTion

SeT CUTTinG DePTH

CUTTinG STRaiGHT eDGeS

DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for

which it was designed.

Содержание HD-101R Pro24 JCS

































































Результаты поиска

Содержание HD-101R Pro24 JCS

Отзывы:

Похожие инструкции для HD-101R Pro24 JCS

Бренды по названию

Популярные бренды

MK Diamond Products HD-101R Pro24 JCS, Руководство пользователя

Результаты поиска

Содержание HD-101R Pro24 JCS

Отзывы:

Похожие инструкции для HD-101R Pro24 JCS

Бренды по названию

Популярные бренды