MK Diamond Products HD-101R Pro24 JCS Скачать руководство пользователя страница 35

Страница: 35 / 64

(A)

Clean the Water Pump

suction of all debris.

(B)

Place the Water Pump

In an external container.

(C)

Run the MK-101 until clear

water is seen at the blade

cooling ports (Approx. 1 min-

ute).

Ensure the saw is disconnected before completing the remainder of the

cleanup process.

(D)

Remove the Water Basin.

Ensure water is not forced into the motor casing when cleaning.

(E)

Clean the Movable Cutting

Table Guide Bar.

(F)

Clean the Movable Cutting

Table Roller Wheel Frame

Support.

(G)

Clean the remainder of the

MK-101.

CaUTion

HD-101R Pro24

CleanUP

CleanUP
noTeS:

1. If an external water source was used, steps A through C may be skipped.

2. Dispose of waste water in accordance with applicable Federal, State and Local laws.

Содержание HD-101R Pro24 JCS

































































Результаты поиска

Содержание HD-101R Pro24 JCS

Отзывы:

Похожие инструкции для HD-101R Pro24 JCS

Бренды по названию

Популярные бренды

MK Diamond Products HD-101R Pro24 JCS, Руководство пользователя

Результаты поиска

Содержание HD-101R Pro24 JCS

Отзывы:

Похожие инструкции для HD-101R Pro24 JCS

Бренды по названию

Популярные бренды