MK Diamond Products HD-101R Pro24 JCS Скачать руководство пользователя страница 24

Страница: 24 / 64

Shaft Lock

Pushbutton

(A)

Position Movable Cutting Table

to the front of the saw and

raise the Blade Guard by

loosening the wingnut.

(B)

Locate the Shaft Lock push

button on the underside

of the Cutting Head.

(C)

Depress and hold the Shaft

Lock pushbutton and remove

Retaining Nut and Outer Flange

using the Blade Wrench.

(D)

Install Diamond Blade

onto Blade Shaft.

(E)

Verify the Blade is seated on

the Blade Shaft and direction

of rotation is correct.

(F)

Install Retaining Nut and Outer

Flange, depress and hold the

Shaft Lock pushbutton

and tighten Retaining Nut.

HD-101R Pro24

aSSeMBlY

Diamond Blade installation

noTe: When installing the Retaining Nut, do not “cross-thread” and DO NOT over tighten.

Содержание HD-101R Pro24 JCS

































































Результаты поиска

Содержание HD-101R Pro24 JCS

Отзывы:

Похожие инструкции для HD-101R Pro24 JCS

Бренды по названию

Популярные бренды

MK Diamond Products HD-101R Pro24 JCS, Руководство пользователя

Результаты поиска

Содержание HD-101R Pro24 JCS

Отзывы:

Похожие инструкции для HD-101R Pro24 JCS

Бренды по названию

Популярные бренды