MK Diamond Products HD-101R Pro24 JCS Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 64

background image

22

UniVeRSal STanD

CaUTion

TRanSPoRT

The MK-101 is designed with a rigid frame and

removable Cutting Head. Two people are required

to transport the MK-101 with the Cutting Head in-

stalled. Remove the Cutting Head if one person is

transporting the saw (see Cutting Head Installation

and Removal in the following section).

Lift Point

Lift Point

Lift the saw using the

lift points shown.

1. The MK-101 weighs approximately one hundred and thirty (130) pounds.

2. Never transport the MK-101 with water in the Water Basin.

The HD-101R Pro24 weighs approximately one hundred and thirty (130) pounds;

follow the guidelines for transport in the TRANSPORT section, when placing it on

the stand.

HD-101R Pro24

TRanSPoRT

(C)

Ensure saw frame is posi-

tioned correctly

(D)

Reinstall the Water Basin

(A)

Open the Stand and place on

flat surface

(B)

Remove Water Basin and

place saw on stand

«
...
20
21
22
23
24
...
»

Содержание HD-101R Pro24 JCS

































































Отзывы:

Нет отзывов

Похожие инструкции для HD-101R Pro24 JCS

Бренд: Makita Страницы: 24

Бренд: Makita Страницы: 4

Бренд: F.F. Group Страницы: 40

Бренд: Ozito Страницы: 6

Бренд: Neilsen Страницы: 29

Бренд: Omcan Страницы: 24

Бренд: Tradesman Страницы: 26

Бренд: EarthWise Страницы: 48

Бренд: Dake Страницы: 24

Бренд: F.F. Group Страницы: 68

Бренд: DWT Страницы: 133

Бренд: DWT Страницы: 160

Бренд: Ferm Страницы: 60

Бренд: HOLZMANN MASCHINEN Страницы: 42

Бренд: HOLZMANN MASCHINEN Страницы: 52

Бренд: HOLZMANN MASCHINEN Страницы: 56

Бренд: Scheppach Страницы: 68

Бренд: Scheppach Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды