Press the “
SET” switch.
The day of the week is committed and the
mark changes
from flashing to lit.
The “current time” flashes in the on timer display area and
“
” is displayed in the display area.
Timer operation is performed based on the time adjusted with the steps described in this section.
Make sure to adjust the remote controller to the current time correctly.
ADJUSTING THE TIME
Press the
or
switch.
Set the
mark displayed above the days of the week to
indicate the current day of the week.
Press
to move to the right and
to move to the left.
“
” and “
” are displayed
alternately.
Note: If you press the “
RESET” switch, the remote comtroller
will return to one screen earlier and display “
”.
2
3
4
●
If you press the “
” switch while in the timer setting mode, the remote controller exits from the timer mode
and returns to the original display. Please be aware that settings that have not been committed become invalid.
●
If you do not press any switches for 60 seconds after entering the timer mode, the remote controller automatically exits from the
timer mode and returns to the original display.
NOTE
Press the
or
switch.
“
” and “
” are displayed
alternately.
Adjust the displayed time to the current time.
●
Press the
or
switch briefly to increase or decrease
the displayed value by 1 minute.
●
If you continue pressing the
or
switch, the display
will change in increments of 10 minuutes.
Note: If you press the “
RESET” switch, the remote
controller will return to one screen earlier.
Press the “
SET” switch.
The time display changes from flashing to lit.
“
” is displayed and the current time is set.
After 2 seconds, the remote controller returns to the timer
mode selection screen and displays “
”.
Step 1
5
Press the “
SET” switch.
The sleep timer has been set.
The air conditioning system starts operating if the sleep timer
is set while the air conditioning system is stopped.
“
” is displayed in the display area. The
display then returns to the timer mode selection screen as
shown below.
Step 2
<If set to turn off after 10 hours>
“
” (lit)
“
” (lit for 2 seconds)
‚
“
” (lit)
“
” (lit)
After the setting, the remaining time is displayed in decre-
ments of 1 hour as the time passes. The air conditioning
system stops operating when the set time has elapsed. The
time display also turns off.
Press the “
SET” switch.
The remote controller goes into the sleep timer mode.
[Example] “
” flashes and
“
” turns on.
Press the
or
switch.
The display changes in the order of “
”,
“
” etc., to “
” and then
“
”. Select the desired number of hours.
“
” and “
” are displayed
alternately.
Note: If you press the “
RESET” switch, the remote controller
will return to on screen earlier and display “
”.
Step 2
5
3
4
In this mode, the air conditioning system stops operating when the set time has elapsed.
SLEEP TIMER MODE
Press the “
” switch once.
This completely ends the time setting procedure.
●
If you press the “
”
switch while in the timer setting mode, the remote controller exits from the timer mode
and returns to the original display.
●
If you do not press any switches for 60 seconds after entering the timer mode, the remote controller automatically exits from the
timer mode and returns to the original display.
Press the “
SET” switch.
The remote controller goes into the adjusting the time mode.
The display area shows the following:
“
” (
flashes)
“
” (Current time)
“
”
5
NOTE
6
2,4,6
3,5
1
7
Press the “
TIMER” switch.
The remote controller goes into the timer mode.
The “current day of the week” and “current time” are displayed and the
subsequent procedures are automatically displayed in the following order.
“
”
‡
“
”
‡
“
”
1
Press the
switch one time.
“
”
‚
“
” (first press)
6
2,4
6
3,5
1
Press the “
TIMER” switch.
The remote controller goes into the timer mode.
The “current day of the week” and “current time” are displayed and the
subsequent procedures are automatically displayed in the following order.
“
”
‡
“
”
‡
“
”
1
2
Press the “
” switch once time setting is
finished.
7
NOTE
PCA012A001J_E_P05
06.9.6, 10:39
5
