background image

Press the “ 

 LOUVER” switch at the position

you want to stop/fix the louver.

The display stops and the following is displayed, then the
swing louver is stopped and fixed.

(If fixed at position 1)

Press the “ 

 LOUVER” switch while the air con-

ditioning system is operating and the swing louver is

stopped.

The swing louver moves up and down continuously and
“ 

 ” is displayed for 3 seconds.

To Fix the Position of the Swing Louver

Press the “ 

 LOUVER” switch once while the swing

louver is moving.
The four available directions in which the swing louver can be
positioned are displayed for 2 seconds each in the order
shown left.

2

1

1

AIRFLOW ADJUSTMENT BY THE LOUVER SWITCH
 (FOR INDOOR UNITS WITH THE AUTO SWING FUNCTION)

HOW TO ADJUST THE AIRFLOW DIRECTION

To Move the Swing Louver

To Fix the Position of the Swing Louver

Recommended Louver Fix Positions

If you want to fix the louver at this
position, make sure to turn the
vertical louver to the left or right (in
the case of FDE).

Cool/Dry

Heat

14

USING THE AIR CONDITIONING SYSTEM IN A COMFORTABLE MANNER

Clean the filer frequently.

 Page18

If the filter is clogged...

The cooling/heating efficiency becomes lower. Moreover, electricity is wasted and the operation makes more noise.

A clogged filter may cause failures.

Dew may form and drop during the cooling operation.

Do not block the inlet and outlet
openings of the indoor and outdoor
units

Excessive force must not be applied to the air

conditioning system; doing so may lead to fail-

ure.

Set a moderate room temperature

Too much cooling or heating is not good for your

health. It is also a waste of electricity.

Block direct sunlight and prevent draft

Block direct sunlight with window blinds and curtains

at cooling. Close the windows and doors except when

ventilation is necessary.

The filter should be cleaned

whenever the “FILTER

CLEANING” message is

displayed, as well as at the end

of cooling and heating seasons.

Adjust the airflow direction properly

Do not subject your skin to the airflow from the

air conditioning system for prolonged periods

of time. Protect small animals and plants from

such direct airflow as well.

If your feet feel cold at heating

If the ceiling is high and the warm airflow does

not circulate down to your floor area suffi-

ciently, it is recommended to use a circulation

fan. Consult the dealer for the details.

Stop the operation and turn the
power supply off if there are any
possibilities of lightning strikes
during a thunderstorm

Failure to do so may lead to failure of the air

conditioning system.

When “ 

 ” (PREPARATION OF HEATING ) is displayed,

the swing louver is automatically set at the horizontal position.
When heater preparation is completed and the air conditioning system is
switched to normal operation, the position of the swing louver returns to
the set position.

REQUEST

Horizontal position

The swing louver may be broken if you attempt to move it forcefully with your hands. Do not attempt to move it with your hands.

Do not direct the airflow downward for extended periods of time at cooling operation. Dew may form on the side panel and drop
from it (in the case of FDE).

1

VENTILATION MODE OPERATION (WHEN A VENTILATOR IS INSTALLED)

NON-LINKED VENTILATION OPERATION

LINKED VENTILATION OPERATION

NOTE

If no ventilator is connected, nothing will happen when the ventilation switch is pressed. ("Operation invalid" is displayed.)

NOTE

Operation is invalid even if the ventilation switch is pressed.

When the ventilator is set to "NO VENTI LINK" (Ventilation not linked), the ventilator can be set to ON/OFF
by itself, without regard to the operation or stopping of the air conditioner. When the ventilator is set to
"VENTI LINK SET" (Ventilation linked), the ventilator will operate when the air conditioner operates.

Press the “ 

 VENTI” switch.

“ 

 ” is displayed, and ventilation operation begins.

1

Press the “ 

 ” switch.

If a ventilator is connected, ventilation will operate automati-

cally. “ 

 ” is displayed.

1

Stop

Stop

Press the “ 

 VENTI” switch a second

time.

Press the “ 

 ” switch a scond time.

PCA012A001H_E_P14

05.11.16, 12:22

14

Содержание MULTI-SERIES





















Отзывы: