manualshive.com logo in svg

Mitsubishi FR - S500, Инструкция по эксплуатации

Поделиться
Скачать
Mitsubishi FR - S500 Скачать руководство пользователя страница 77

67

Explanation of functions (parameters)

2

F

UNCT

IO

NS

2.3.5

Acceleration/deceleration time (Pr. 7 

, Pr. 8 

, 

Pr. 20 

, Pr. 44 

, Pr. 45 

)

CAUTION

1. The multi-speed settings override the main speeds (across terminals 2-5, 4-

5, setting dial). When the multi-speed settings and setting dial are used in

the combined operation mode (Pr. 79=3), the multi-speed settings have

precedence.

2. The multi-speeds can also be set in the PU or external operation mode.

3. For 3-speed setting, if two or three speeds are simultaneously selected,

priority is given to the set frequency of the lower signal.

4. Pr. 24 to Pr. 27 and Pr. 80 to Pr. 87 settings have no priority between them. 

5. The parameter values can be changed during operation.

6. When using this function with the jog signal, the jog signal has precedence.

REMARKS

The frequency-set external terminals have the following priority:

Jog > multi-speed operation > AU (terminal 4) > terminal 2

♦

Related parameters

♦

•

Maximum, minimum frequency setting 

⇒

 Pr. 1 "maximum frequency", Pr. 2 "minimum frequency" 

(refer to page 64)

•

Assignment of signals RH, RM, RL, REX to terminals 

⇒

 Pr. 60 to Pr. 63 (input terminal function 

selection) (refer to page 98)

•

External operation mode setting 

⇒

 Pr. 79 "operation mode selection" (refer to page 109)

•

Computer link mode 

⇒

 Pr. 79 "operation mode selection" (refer to page 109), communication 

parameter n10 "link startup mode selection" (refer to page 148)

•

Speed command source 

⇒

 Communication parameter n9 "speed command source"

(refer to page 147)

Used to set motor acceleration/
deceleration time.
Set a larger value for a slower 
speed increase/decrease or a 
smaller value for a faster speed 
increase/decrease.

Parameter

Name

Factory 

Setting

Setting 

Range

Remarks

7

Acceleration time

5s

0 to 999s

----------

8

Deceleration time

5s

0 to 999s

----------

20

Acceleration/

deceleration reference 

frequency

60Hz

1 to 120Hz Setting is enabled when 

Pr. 30 = "1".

44

Second acceleration/

deceleration time

5s

0 to 999s Setting is enabled when 

Pr. 30 = "1".

45

Second deceleration 

time

- - -

0 to 999s,

 - - -

- - -: 

acceleration time= 

deceleration time. 

Setting is 

enabled when

Pr. 30 = "1".

Running
frequency

Acceleration

time

Deceleration

time

Time

Pr.20

Out

put

 fr

e

quen

cy

 (Hz

)

Pr.7
Pr.44

Pr.8
Pr.45

Acceleration

Deceleration

Constant speed

Содержание FR - S500





































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды