Mitsubishi Electric SLZ-KA25VA, Руководство по эксплуатации

Страница: 11 / 172

11
ON/OFF TEMP
°C
°C
ON/OFF TEMP.
°C
°C
ON/OFF
ERROR CODE
ON/OFF
°C
°C
ERROR CODE
ON/OFF
CALL:XXXX
XXX:XXX
If you have entered contact number to be called in the event of a prob-
lem, the screen displays this number. (You can set this up under Function
Selection of remote controller. For information, refer to section 8.)
7. Other Functions
7.2. Other indications
7.2.1. Centrally Controlled
N
When flashes continuously
Displayed when another indoor unit connected to the outdoor unit is
already operating in a different operation mode.
Match with the operation mode of the other indoor unit.
N When mode switched after display flashes
Displayed when operation mode is restricted for each season by central
controller, etc.
Use another operation mode.
●
Displayed when operation is controlled by central controller, etc.
Restricted operations are shown below.
• ON/OFF (including timer operation)
• Operation
mode
• Set temperature
Note:
May also be individually restricted.
7.2.2. Flashing Mode Indicator
Indoor Unit’s
Refrigerant
Address Error Code Indoor Unit No.
Alternating
Display
Error Code
When the Check button is pressed:
ON lamp
(Flashing)
7.2.3. Error Codes indication
●
If the ON lamp and error code are both flashing: This means that the air
conditioner is out of order and operation has been stopped (and cannot
resume). Take note of the indicated unit number and error code, then switch
off the power to the air conditioner and call your dealer or servicer.
●
If only the error code is flashing (while the ON lamp remains lit): Opera-
tion is continuing, but there may be a problem with the system. In this
case, you should note down the error code and then call your dealer or
servicer for advice.
* If you have entered contact number to be called in the event of a
problem, push the Check button to display it on the screen. (You
can set this up under Function Selection of remote controller. For
information, refer to section 8.)
8. Function Selection
Function selection of remote controller
The setting of the following remote controller functions can be changed using the remote controller function selection mode. Change the setting when
needed.
Item 1 Item 2 Item 3 (Setting content)
1. Change Language
(“CHANGE
LANGUAGE”)
Language setting to display • Display in multiple languages is possible
2. Function limit
(“FUNCTION
SELECTION”)
(1) Operation function limit setting (operation lock) (“LOCKING
FUNCTION”)
• Setting the range of operation limit (operation lock)
(2) Use of automatic mode setting (“SELECT AUTO MODE”) • Setting the use or non-use of “automatic” operation mode
(3) Temperature range limit setting (“LIMIT TEMP FUNCTION”) • Setting the temperature adjustable range (maximum, minimum)
3. Mode selection
(“MODE
SELECTION”)
(1) Remote controller main/sub setting (“CONTROLLER
MAIN/SUB”)
• Selecting main or sub remote controller
* When two remote controllers are connected to one group, one con-
troller must be set to sub.
(2) Use of clock setting (“CLOCK”) • Setting the use or non-use of clock function
(3) Timer function setting (“WEEKLY TIMER”) • Setting the timer type
(4) Contact number setting for error situation (“CALL.”) • Contact number display in case of error
• Setting the telephone number
4. Display change
(“DISP
MODE
SETTING”)
(1) Temperature display °C/°F setting (“TEMP MODE °C/°F”) • Setting the temperature unit (°C or °F) to display
(2) Suction air temperature display setting (“ROOM TEMP
DISP SELECT”)
• Setting the use or non-use of the display of indoor (suction) air tem-
perature
(3) Automatic cooling/heating display setting (“AUTO MODE
DISP C/H”)
• Setting the use or non-use of the display of “Cooling” or “Heating”
display during operation with automatic mode