4
Installing the re
I
rigerant piping
Drainage piping wor
N
Outdoor unit drainage pipe connection
:KHQGUDLQSLSLQJLVQHFHVVDU\XVHWKHGUDLQVRFNHWRUWKHGUDLQSDQRSWLRQ
Drain socket
PAC-SG61DS-E
Drain pan
PAC-SH97DP-E
1
Caution
1
Follow ordinance of your governmental organization for technical standard related
to electrical equipment, wiring regulations and guidance of each electric power
company.
2
:LULQJIRUFRQWUROKHUHLQDIWHUUHIHUUHGWRDVWUDQVPLVVLRQOLQHVKDOOEHFPRU
PRUHDSDUWIURPSRZHUVRXUFHZLULQJVRWKDWLWLVQRWLQÀXHQFHGE\HOHFWULFQRLVH
from power source wiring. (Do not insert transmission line and power source wire
in the same conduit.)
3
Be sure to provide designated grounding work to outdoor unit.
4
Give some allowance to wiring for electrical part box of indoor and outdoor units,
because the box is sometimes removed at the time of service work.
5
1HYHUFRQQHFWWKHPDLQSRZHUVRXUFHWRWHUPLQDOEORFNRIWUDQVPLVVLRQOLQH,I
connected, electrical parts will be burnt out.
6
Use 2-core shield cable for transmission line. If transmission lines of different
systems are wired with the same multiplecore cable, the resultant poor transmit-
ting and receiving will cause erroneous operations.
Electrical wor
N
7
2QO\WKHWUDQVPLVVLRQOLQHVSHFL¿HGVKRXOGEHFRQQHFWHGWRWKHWHUPLQDOEORFNIRU
outdoor unit transmission.
(Transmission line to be connected with indoor unit : Terminal block TB3 for
transmission line, Other : Terminal block TB7 for centralized control)
Erroneous connection does not allow the system to operate.
8
In case to connect with the upper class controller or to conduct group operation in
different refrigerant systems, the control line for transmission is required between
the outdoor units each other.
Connect this control line between the terminal blocks for centralized control. (2-
wire line with no polarity)
:KHQFRQGXFWLQJJURXSRSHUDWLRQLQGLIIHUHQWUHIULJHUDQWV\VWHPVZLWKRXWFRQQHFW
-
ing to the upper class controller, replace the insertion of the short circuit connector
IURP&1RIRQHRXWGRRUXQLWWR&1
9
Group is set by operating the remote controller.
0
:KHQFRQQHFWLQJWKH&211(&7,21.,73$&/90-DQGDQ0VHULHVLQGRRU
XQLWUHIHUWRWKHLQVWDOODWLRQPDQXDOIRUWKH&211(&7,21.,7
7KH ¿JXUH WR WKH OHIW LV DQ H[DPSOH
only. The stop valve shape, service port
position, etc., may vary according to the
model.
* Turn
section
A
only.
(Do not further tighten sections
A
and
B
together. )
C
Charge hose
D
Service port
Precautions when using the charge
Y
al
Y
e
Fig
4-
Do not tighten the service port too much when installing it, otherwise, the valve core
could be deformed and become loose, causing a gas leak.
After positioning section
B
in the desired direction, turn section
A
only and tighten it.
Do not further tighten sections
A
and
B
together after tightening section
A
.
Fig
4-
4
Additional re
I
rigerant charge
Additional re
I
rigerant charge
Refrigerant for the extended piping is not included in the outdoor unit when the unit is
shipped from the factory. Therefore, charge each refrigerant piping system with addi-
tional refrigerant at the installation site. In addition, in order to carry out service, enter
the size and length of each liquid pipe and additional refrigerant charge amounts in
the spaces provided on the “Refrigerant amount” plate on the outdoor unit.
Calculation o
I
additional re
I
rigerant charge
&DOFXODWH WKH DGGLWLRQDO FKDUJH XVLQJ WKH OLTXLG SLSH VL]H DQG OHQJWK RI WKH H[
-
tended piping and total capacity of connected indoor units.
&DOFXODWHWKHDGGLWLRQDOUHIULJHUDQWFKDUJHXVLQJWKHSURFHGXUHVKRZQWRWKHULJKW
and charge with the additional refrigerant.
)RU DPRXQWV OHVV WKDQ NJ URXQG XS WKH FDOFXODWHG DGGLWLRQDO UHIULJHUDQW
charge.
(For example, if the calculated charge is 6.01 kg, round up the charge to 6.1 kg.)
([DPSOH!
Outdoor model : P125
,QGRRU 3N: $¡ P D ¡ P
3N:
E ¡ P
3N:
F ¡ P
3N:
G ¡ P
3N:
H ¡ P
The total length of each liquid line is as follows:
ø9.52 : A + a = 30 + 15 = 45 m
ø6.35 : b + c + d + e = 10 + 10 + 20 + 10 = 50 m
The total capacity of connected indoor unit is as follows:
7.1 + 4.5 + 2.8 + 2.2 + 5.6 = 22.2
&DOFXODWLRQH[DPSOH!
Additional refrigerant charge
At the conditions
below:
50 ×
19.0
+ 45 ×
50.0
+ 3.0 = 6.2 kg
1000
1000
$GGLWLRQDO&KDUJH!
Calculation o
I
re
I
rigerant charge
Pipe size
Liquid pipe
+
Pipe size
Liquid pipe
+
Pipe size
Liquid pipe
+
Total capacity of
connected indoor
units
Amount for
the indoor
units
ø6.35
ø9.52
ø12.7
±N:
2.5 kg
(m)
u
19.0 (g/m)
(m)
u
50.0 (g/m)
(m)
u
92.0 (g/m)
±N:
3.0 kg
N:±
3.5 kg
Included re
I
rigerant a
P
ount when shipped
I
ro
P
the
I
actor
\
Included refrigerant amount
7.3 kg
