Mitsubishi Electric PRH-P10MYA Скачать руководство пользователя страница 71

Страница: 71 / 87

- 68 -

Symptom and operation when normal

1. No remote controller display

2. Remote controller displays “H0” un-

changed.

3. When remote controller operation

switch pressed, operation display
appears but immediately disap-
pears.

4. Does not beep and air conditioner

does not operate even when oper-
ated with wireless remote control-
ler.
(Operation display appears on wire-
less remote controller.)

5. When operated with wireless re-

mote controller, beeps but does not
operate.

6. Remote controller display is normal

and cooling operation is performed,
but without any capacity (does not
cool).

Cause

(1) DC14V is not supplied to remote con-

troller.
(No power O display on liquid crystal
panel.)

(2) DC14V is supplied to remote controller

but nothing is displayed.
- “H0” not displayed
- “H0” displayed

(1) Remote controller displays “H0” for

maximum of 2 minutes for starting after
power turned on.

(2) Indoor-remote controller communication

faulty.

(3) Outdoor-indoor controller boards

communication faulty.

(1) Operation switch is disabled for approxi-

mately 30 seconds after function select
operation from remote controller is re-
leased.

(1) Wireless remote controller and

indoor-side controller board pair
number setting mismatched.

(2) Cause of item 1.

(1) Air conditioner does not operate for a

maximum of 2 minutes after the power
is turned on.

(2) Set to local operation prohibit mode.

- Remote start/stop adapter is con-

nected to CN32 on indoor-side
controller board.

- Air conditioner is connected to

MELANS and is set to local operation
prohibit mode from centralized control-
ler, etc.

(3) Cause of item 2.

(1) Insufficient refrigerant.
(2) Filter clogged.
(3) Outdoor-side heat exchanger clogged.
(4) Air duct short cycle.
(5) LEV malfunction

Symptom judgment and remedy

(1) Check LED2 on indoor-side controller board.

1) Steady light

Check remote controller wire open or faulty
contact.

2) Flashing

Check for remote controller wire short.

3) Not lit

Check outdoor-side controller refrigerant
address.

(2) Make the following judgment:

- When “H0” is not displayed, remote control-

ler is faulty.

- When “H0” is displayed, see item 2.

(1) Normal operation.
(2) Remote controller self-diagnosis.
(3) When outdoor-indoor controller boards cannot

communicate, “H0” is displayed for a
maximum 6 minutes.
Check LED3 on indoor-side controller board.

1) Does not flash

Check indoor/outdoor controller boards
connection cable for erroneous wiring.
(S1 and S2 or S3 open)

2) Flashes

Indoor/outdoor contorller boards connection
cable is normal.

(1) Normal operation.

(1) Check pair number setting.
(2) Item check of item 1.

(1) Normal operation.
(2) Normal operation.
(3) Item check of item 2.

(1) - When there is leakage, discharge tempera-

ture rises. Therefore, check by measuring
temperature.

- Check for gas leakage from piping connec-

tions, etc.

(2) Open intake grille and check filter. Clean filter,

and remove dust and dirt.

(3) - Since both indoor-side piping temperature

and outlet pressure rise when filter clogged,
judge by measuring outlet pressure.

- Clean heat exchanger.

(4) Remove obstruction.
(5) Check refrigerant circuit operation state.

Содержание PRH-P10MYA
























































































Результаты поиска

Содержание PRH-P10MYA

Отзывы:

Похожие инструкции для PRH-P10MYA

Бренды по названию

Популярные бренды

Mitsubishi Electric PRH-P10MYA, Техническое и сервисное руководство

Результаты поиска

Содержание PRH-P10MYA

Отзывы:

Похожие инструкции для PRH-P10MYA

Бренды по названию

Популярные бренды