Mitsubishi Electric MUY-GL09NA Скачать руководство пользователя

Страница: 66 / 76

OPERATING PROCEDURE

PHOTOS/FIGURES

Photo 4

Photo 5

5HPRYLQJWKHLQYHUWHUDVVHPEO\LQYHUWHU3&ERDUG

(1) Remove the cabinet and panels. (Refer to section 1.)
(2) Disconnect the lead wire to the reactor and the following

connectors:

<Inverter

P.C.

board>

CN721 (R.V. coil) (

MUZ

)

CN722 (Defrost heater and heater protector) (

MUZ-

GL09/12/15NAH

)

CN931, CN932 (Fan motor)
CN641 (Defrost thermistor (

MUZ

) and discharge tempera-

ture thermistor)

CN643 (Ambient temperature thermistor)
CN644 (Outdoor heat exchanger temperature thermistor)
CN724 (LEV)

(3) Remove the compressor connector (CN61).
(4) Remove the screws fixing the heat sink support and the

separator.

(5) Remove the fixing screws of the terminal block support and

the back panel.

(6) Remove the inverter assembly.
(7) Remove the screw of the ground wire and screw of the ter-

minal block support.

(8) Remove the heat sink support from the P.C. board support.
(9) Remove the screw of the inverter P.C. board and remove the

inverter P.C. board from the P.C. board support.

Photo 6

5HPRYLQJ59FRLO

(1) Remove the cabinet and panels. (Refer to section 1.)
(2) Disconnect the following connectors:
<Inverter

P.C.

board>

CN721 (R.V. coil) (

MUZ

)

(3) Remove the R.V. coil.

Photo 7

Screws of the heat sink
support and the separator

Screws of the terminal block
support and the back panel

Screws of the
conduit cover

Screw of the
conduit plate

Heat sink

Screw of the
ground wire

Screw of the
Terminal block
support

Screw of the
inverter P.C. board

Heat sink support

P.C. board
support

Terminal
block
support

*U2 model does not
have a screw on the
heat sink support.

OBH733G

Содержание MUY-GL09NA













































































Результаты поиска

Содержание MUY-GL09NA

Отзывы:

Похожие инструкции для MUY-GL09NA

Бренды по названию

Популярные бренды

Mitsubishi Electric MUY-GL09NA, Руководство по обслуживанию

Результаты поиска

Содержание MUY-GL09NA

Отзывы:

Похожие инструкции для MUY-GL09NA

Бренды по названию

Популярные бренды