manualshive.com logo in svg

Mitsubishi Electric MUY-GL09NA, Руководство по обслуживанию

Поделиться
Скачать
Mitsubishi Electric MUY-GL09NA Скачать руководство пользователя страница 54

54

-&KHFNRISRZHUVXSSO\

Is there voltage 208/230 V AC 
between the indoor terminal 
block S1 and S2?

Yes

No

Replace the indoor 
electronic control P.C. 
board.

Rectify indoor/outdoor 
connecting wire.

Yes

If lights up, OK.
If blinks, refer to 10-3. 

Does the upper lamp of the 
OPERATION INDICATOR lamp on 
the indoor unit light up?

Does LED on the inverter P.C. 
board light up or blink?
(Refer to 10-6.1.)

No

Replace the inverter 
P.C. board.

Is there Bus-bar voltage 260 - 370 V 
DC between DB61 (+) and DB61 (–) 
(

MUZ-GL09/12/15/18, MUY-

GL09/12/15/18

)/294 - 370 V DC 

between JP715 (+) and JP30 (–) 
(

MUZ-GL24, MUY-GL24

) on the 

inverter P.C. board? (Refer to 10-6.1.)

No

Check the electric parts in main circuit.

Yes

Yes

No

Disconnect the connector between the 
compressor and the power module 
(IC700) (

MUZ-GL09/12/15/18, MUY-

GL09/12/15/18

)/IGBT module (IC700) 

(

MUZ-GL24, MUY-GL24

).

Turn ON power supply and press
EMERGENCY OPERATION switch.

294 -370 V DC

JP30

JP715

MUZ-GL09/12/15/18NA  
MUZ-GL09/12/15/18NAH
MUY-GL09/12/15/18NA

MUZ-GL24NA  
MUZ-GL24NAH
MUY-GL24NA

Inverter P.C. board
(Solder side)

DB61

260 - 370 V DC

OBH733G

Содержание MUY-GL09NA













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды