Mitsubishi Electric MUY-GL09NA Скачать руководство пользователя

Страница: 73 / 76

OPERATING PROCEDURE

PHOTOS/FIGURES

5HPRYLQJWKHLQYHUWHUDVVHPEO\LQYHUWHU3&ERDUG

DQGUHOD\3&ERDUG

(1) Remove the cabinet and panels. (Refer to section 1.)
(2) Disconnect the lead wire to the reactor and the following con-

nectors:

<Inverter P.C. board>
CN601 (Defrost heater and heater protector) (

MUZ-GL24NAH

)

CN602 (R.V. coil) (

MUZ

)

CN931, CN932 (Fan motor)
CN671 (Defrost thermistor (

MUZ

), discharge temperature

thermistor and outdoor heat exchanger temperature
thermistor)

CN672 (Ambient temperature thermistor)
CN724 (LEV)

(3) Remove the compressor connector.
(4) Remove the screws fixing the relay panel.
(5) Remove the relay panel.
(6) Remove the ground wires and the lead wires of the inverter

P.C. board.

(7) Remove the screws of the P.B. support.
(8) Remove the inverter P.C. board from the P.B. support.

Photo 5

5HPRYLQJ59FRLO08=

(1) Remove the cabinet and panels. (Refer to section 1.)
(2) Disconnect the following connector:
<Inverter

P.C.

board>

CN602 (R.V. coil) (

MUZ

)

(3) Remove the R.V. coil.

Photo 6

Brazed parts of
4-way valve

Screw of the
R.V. coil (

MUZ

)

Screw of the
relay panel

Screws of the
P.B. support

Inverter P.C.
board

Ground wires

Screws of
the P.B.
support

Screw of the
relay panel

OBH733G

Содержание MUY-GL09NA













































































Результаты поиска

Содержание MUY-GL09NA

Отзывы:

Похожие инструкции для MUY-GL09NA

Бренды по названию

Популярные бренды

Mitsubishi Electric MUY-GL09NA, Руководство по обслуживанию

Результаты поиска

Содержание MUY-GL09NA

Отзывы:

Похожие инструкции для MUY-GL09NA

Бренды по названию

Популярные бренды