Mitsubishi Electric MUY-GL09NA страница 40 Скачать руководство пользователя | Manualshive

Страница: 40 / 76

background image

40

SERVICE FUNCTIONS

9

9-1. CHANGE IN DEFROST SETTING (MUZ)

&KDQJLQJGHIURVWILQLVKWHPSHUDWXUH

<JS> To change the defrost finish temperature, cut/solder the JS wire of the outdoor inverter P.C. board (Refer to 10-6.1.).

Jumper

'HIURVW¿QLVKWHPSHUDWXUH

MUZ-GL09/12/15NA

MUZ-GL09/12/15NAH

MUZ-GL18/24NA

MUZ-GL18/24NAH

JS

Soldered

(Initial setting)

41°F (5°C)

50°F (10°C)

None

(Cut)

50°F (10°C)

64°F (18°C)

9-2. PRE-HEAT CONTROL SETTING (MUZ)

MUZ-GL09/12/15/18

When moisture gets into the refrigerant cycle, it may interfere with the startup of the compressor at low outside tempera-
ture. The pre-heat control prevents this interference. The pre-heat control turns ON when the discharge temperature ther-
mistor is 68°F (20°C) or below. When the pre-heat control turns ON, the compressor is energized. (About 50 W)

MUZ-GL24

Prolonged low load operation, in which the thermostat is OFF for a long time, at low outside temperature [32°F (0°C) or
less] may cause the following troubles. The pre-heat control prevents those troubles.
1) If moisture gets into the refrigerant cycle and freezes, it may interfere the startup of the compressor.
2) If liquid refrigerant collects in the compressor, a failure in the compressor may occur.
The pre-heat control turns ON when the compressor temperature is 68°F (20°C) or below. When the pre-heat control
turns ON, the compressor is energized. (About 70 W)

3UHKHDWFRQWUROVHWWLQJ

<JK>
ON: To activate the pre-heat control, cut JK wire of the inverter P.C. board.
OFF: To deactivate the pre-heat control, solder JK wire of the inverter P.C. board.
(Refer to 10-6.1)

Jumper

3UHKHDWFRQWUROVHWWLQJ

MUZ-GL09/12/15/18NA

MUZ-GL09/12/15/18NAH

MUZ-GL24NA

MUZ-GL24NAH

JK

Soldered

Deactivated

(Initial setting)

Deactivated

Cut

Activated

Activated

(Initial setting)

NOTE:

When the inverter P.C. board is replaced, check the JK wire, and cut/solder them if necessary.

MUZ-GL09NA MUZ-GL09NAH MUY-GL09NA
MUZ-GL12NA MUZ-GL12NAH MUY-GL12NA
MUZ-GL15NA MUZ-GL15NAH MUY-GL15NA
MUZ-GL18NA MUZ-GL18NAH MUY-GL18NA
MUZ-GL24NA MUZ-GL24NAH MUY-GL24NA

OBH733G

«
...
38
39
40
41
42
...
»

Содержание MUY-GL09NA













































































Отзывы:

Нет отзывов

Похожие инструкции для MUY-GL09NA

Бренд: Hamilton Beach Страницы: 2

Бренд: AiroDoctor Страницы: 8

Бренд: Daikin Страницы: 44

Бренд: SPT Страницы: 20

Бренд: TriStar Страницы: 72

Бренд: Mammoth Страницы: 19

Бренд: S&P Страницы: 24

Бренд: Lennox Страницы: 32

Бренд: Haier Group Страницы: 58

Бренд: Carrier Страницы: 22

Бренд: Bryant Страницы: 32

Бренд: Rasonic Страницы: 24

Бренд: Bryant Страницы: 56

Бренд: GE Страницы: 48

Бренд: GE Страницы: 48

Бренд: Daikin Страницы: 72

Бренд: Daikin Страницы: 28

Бренд: Dometic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды