Mitsubishi Electric MUFZ-KJ09NAHZ Скачать руководство пользователя | Manualshive

Страница: 21 / 50

background image

21

SERVICE FUNCTIONS

9

9-1. CHANGE IN DEFROST SETTING

Changing defrost finish temperature

<JS> To change the defrost finish temperature, cut/solder the JS wire of the outdoor inverter P.C. board (Refer to 10-6.1.).

Jumper

Defrost

fi

nish temperature

MUFZ-KJ09/12NAHZ

MUFZ-KJ15/18NAHZ

JS

Soldered

(Initial setting)

41°F (5°C)

50°F (10°C)

None

(Cut)

50°F (10°C)

64°F (18°C)

9-2. PRE-HEAT CONTROL SETTING

MUFZ-KJ09/12

When moisture gets into the refrigerant cycle, it may interfere with the start-up of the compressor at low outside tempera-
ture. The pre-heat control prevents this interference. The pre-heat control turns ON when the discharge temperature ther-
mistor is 68°F (20°C) or below. When the pre-heat control turns ON, the compressor is energized. (About 50 W)

MUFZ-KJ15/18

Prolonged low load operation, in which the thermostat is OFF for a long time, at low outside temperature [32°F (0°C) or
less] may cause the following troubles. The pre-heat control prevents this interference.
1) If moisture gets into the refrigerant cycle and freezes, it may interfer the start-up of the compressor.
2) If liquid refrigerant collects in the compressor, a failure in the compressor may occur.

The pre-heat control turns ON when the compressor temperature is 68°F (20°C) or below. When the pre-heat control
turns ON, the compressor is energized. (About 70 W)

Pre-heat control setting

<JK>
ON: To activate the pre-heat control, cut JK wire of the inverter P.C. board.
OFF: To deactivate the pre-heat control, solder JK wire of the inverter P.C. board.
(Refer to 10-6.1)

Jumper

Pre-heat control setting

MUFZ-KJ09/12NAHZ

MUFZ-KJ15/18NAHZ

JK

Soldered

Deactivated

(Initial setting)

Deactivated

(Initial setting)

Cut

Activated

Activated

NOTE:

When the inverter P.C. board is replaced, check the jumper wires, and cut/solder them if necessary.

MUFZ-KJ09NAHZ MUFZ-KJ12NAHZ MUFZ-KJ15NAHZ MUFZ-KJ18NAHZ

OBH753A

«
...
19
20
21
22
23
...
»

Содержание MUFZ-KJ09NAHZ



















































Отзывы:

Нет отзывов

Похожие инструкции для MUFZ-KJ09NAHZ

Бренд: Panasonic Страницы: 21

Бренд: Daikin Страницы: 108

Бренд: Daikin Страницы: 40

Бренд: Daikin Страницы: 344

MWF-18CRN1-QC1G

Бренд: Akai Страницы: 40

AIR CONDITIONER SYSTEMS

Бренд: DDB Страницы: 12

AIRCOMMAND IBIS

Бренд: Dometic Страницы: 13

4SCU 16LS Series

Бренд: Armstrong Air Страницы: 32

Бренд: GE Страницы: 48

Бренд: TCL Страницы: 33

Бренд: Kogan Страницы: 15

Excelair EPA101A

Бренд: Excelsior Страницы: 16

Бренд: Carrier Страницы: 14

ProShield Plus Ai

Бренд: Oreck Страницы: 10

climaVAIR V 7-025 NW

Бренд: Vaillant Страницы: 26

Бренд: Carrier Страницы: 10

38QHG009D8S Series

Бренд: Carrier Страницы: 92

Бренд: TriStar Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды