Mitsubishi Electric MUFZ-KJ09NAHZ страница 48 Скачать руководство пользователя

Страница: 48 / 50

OPERATING PROCEDURE

PHOTOS

2. Removing the inverter assembly, inverter P.C. board

and relay P.C. board

(1) Remove the cabinet and panels. (Refer to 1.)
(2) Disconnect the lead wire to the reactor and the following con-

nectors:

<Inverter P.C. board>
CN602 (R.V. coil)
CN931, CN932 (Fan motor)
CN671 (Defrost thermistor, discharge temperature thermistor

and outdoor heat exchanger temperature thermistor)

CN672 (Ambient temperature thermistor)
CN724 (LEV)
CN601 (Defrost heater and heater protector)

(3) Remove the compressor connector.
(4) Remove the screws fixing the relay panel.
(5) Remove the relay panel.
(6) Remove the ground wires and the lead wires of the inverter

P.C. board.

(7) Remove the screws of the P.B. support.
(8) Remove the inverter P.C. board from the P.B. support.

Photo 5

Photo 6

3. Removing R.V. coil

(1) Remove the cabinet and panels. (Refer to 1.)
(2) Disconnect the following connector:

CN602 (R.V. coil)

(3) Remove the R.V. coil.

Brazed parts of

4-way valve

Screw of the

R.V. coil

Screw of the

relay panel

Screws of the

P.B. support

Inverter P.C.

board

Ground wires

Screws of

the P.B.

support

Screw of the

relay panel

Screw of the

relay panel

OBH753A

Содержание MUFZ-KJ09NAHZ



















































Результаты поиска

Содержание MUFZ-KJ09NAHZ

Отзывы:

Похожие инструкции для MUFZ-KJ09NAHZ

Бренды по названию

Популярные бренды

Mitsubishi Electric MUFZ-KJ09NAHZ, Руководство по обслуживанию

Результаты поиска

Содержание MUFZ-KJ09NAHZ

Отзывы:

Похожие инструкции для MUFZ-KJ09NAHZ

Бренды по названию

Популярные бренды