Mitsubishi Electric MUFZ-KJ09NAHZ страница 43 Скачать руководство пользователя | Manualshive

Страница: 43 / 50

background image

11-1. MUFZ-KJ09NAHZ MUFZ-KJ12NAHZ

NOTE

: Turn OFF the power supply before disassembly.

OPERATING PROCEDURE

PHOTOS

1. Removing the cabinet

(1) Remove the screw fixing the service panel.
(2) Pull down the service panel and remove it.
(3) Remove the screws fixing the conduit cover.
(4) Remove the conduit cover. (Photo 4)
(5) Remove the screw fixing the conduit plate. (Photo 5)
(6) Remove the conduit plate.
(7) Disconnect the power supply wire and indoor/outdoor

connecting wire.

(8) Remove the screws fixing the top panel.
(9) Remove the top panel.
(10) Remove the screws fixing the cabinet.
(11) Remove the cabinet.
(12) Remove the screws fixing the back panel.
(13) Remove the back panel.

Photo 2

Photo 1

Photo 3

43

(1) Slide the sleeve and check if there is a locking lever or not.

(2) The terminal with this connector has the
locking mechanism.

Slide the sleeve.
Pull the terminal while
pushing the locking
lever.

Hold the sleeve, and
pull out the terminal
slowly.

Connector

Sleeve

Locking lever

<"Terminal with locking mechanism" Detaching points>

The terminal which has the locking mechanism can be detached as shown below.

There are 2 types (refer to (1) and (2)) of the terminal with locking mechanism.

The terminal without locking mechanism can be detached by pulling it out.

Check the shape of the terminal before detaching.

DISASSEMBLY INSTRUCTIONS

Back
panel

Service
panel

Screws of
the cabinet

Screws of
the top panel

Direction
to remove

Screws of
the cabinet

Hooks

Screw of the

cabinet

Screws
of the
back
panel

Screws of
the terminal block
support and the
back panel

11

Screws of the
top panel

Screws of the
cabinet

OBH753A

«
...
41
42
43
44
45
...
»

Содержание MUFZ-KJ09NAHZ



















































Отзывы:

Нет отзывов

Похожие инструкции для MUFZ-KJ09NAHZ

Бренд: Haier Страницы: 52

Бренд: AAF Страницы: 4

Бренд: Valeo Страницы: 15

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 48

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 18

Бренд: Panasonic Страницы: 14

Бренд: Panasonic Страницы: 112

MTA8F128R5I Series

Бренд: Technibel Climatisation Страницы: 47

Бренд: Daikin Страницы: 40

Бренд: Bang & Olufsen Страницы: 38

MDV DCTB-24R32IVT IN

Бренд: aircon Страницы: 84

Бренд: WAGNER Страницы: 5

Premium CR 7926

Бренд: camry Страницы: 156

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды