Mitsubishi Electric MUFZ-KJ09NAHZ Скачать руководство пользователя

Страница: 45 / 50

OPERATING PROCEDURE

PHOTOS

4. Removing the discharge temperature thermistor,

defrost thermistor, outdoor heat exchanger tempera-
ture thermistor and ambient temperature thermistor

(1) Remove the cabinet and panels. (Refer to 1.)
(2) Disconnect the lead wire to the reactor and the following con-

nectors:
<Inverter P.C. board>

CN641 (Defrost thermistor and discharge temperature ther-

mistor)

CN643 (Ambient temperature thermistor)
CN644 (Outdoor heat exchanger temperature thermistor)

(3) Pull out the discharge temperature thermistor from its holder.
(4) Pull out the defrost thermistor from its holder. (Photo 6)
(5) Pull out the outdoor heat exchanger temperature thermistor

from its holder. (Photo 6)

(6) Pull out the ambient temperature thermistor from its holder.

Photo 8

Photo 9

Photo 10

Discharge temperature thermistor

Screw of the

R.V. coil

Defrost thermistor

Outdoor heat
exchanger tempera-
ture thermistor

Ambient temperature
thermistor

OBH753A

Содержание MUFZ-KJ09NAHZ



















































Результаты поиска

Содержание MUFZ-KJ09NAHZ

Отзывы:

Похожие инструкции для MUFZ-KJ09NAHZ

Бренды по названию

Популярные бренды

Mitsubishi Electric MUFZ-KJ09NAHZ, Руководство по обслуживанию

Результаты поиска

Содержание MUFZ-KJ09NAHZ

Отзывы:

Похожие инструкции для MUFZ-KJ09NAHZ

Бренды по названию

Популярные бренды