Mitsubishi Electric MUFZ-KJ09NAHZ Скачать руководство пользователя

Страница: 44 / 50

OPERATING PROCEDURE

PHOTOS

Photo 4

Photo 5

2. Removing the inverter assembly, inverter P.C. board

(1) Remove the cabinet and panels. (Refer to 1.)
(2) Disconnect the lead wire to the reactor and the following

connectors:

CN721 (R.V. coil)
CN722 (Defrost heater and heater protector)
CN931, CN932 (Fan motor)
CN641 (Defrost thermistor and discharge temperature ther-

mistor)

CN643 (Ambient temperature thermistor)
CN644 (Outdoor heat exchanger temperature thermistor)
CN724 (LEV)

(3) Remove the compressor connector (CN61).
(4) Remove the screws fixing the heat sink support and the

separator.

(5) Remove the fixing screws of the terminal block support and

the back panel.

(6) Remove the inverter assembly.
(7) Remove the screw of the ground wire and screw of the ter-

minal block support.

(8) Remove the heat sink support from the P.C. board support.
(9) Remove the screw of the inverter P.C. board and remove the

inverter P.C. board from the P.C. board support.

Photo 6

3. Removing R.V. coil

(1) Remove the cabinet and panels. (Refer to 1.)
(2) Disconnect the following connectors:

CN721 (R.V. coil)

(3) Remove the R.V. coil.

Photo 7

Screws of the heat sink
support and the separator

Screws of the terminal block
support and the back panel

Screws of the
conduit cover

Screw of the
conduit plate

Heat sink

Screw of the

ground wire

Screw of the

Terminal block

support

Screw of the

inverter P.C. board

Heat sink support

P.C. board

support

Terminal

block

support

OBH753A

Содержание MUFZ-KJ09NAHZ



















































Результаты поиска

Содержание MUFZ-KJ09NAHZ

Отзывы:

Похожие инструкции для MUFZ-KJ09NAHZ

Бренды по названию

Популярные бренды

Mitsubishi Electric MUFZ-KJ09NAHZ, Руководство по обслуживанию

Результаты поиска

Содержание MUFZ-KJ09NAHZ

Отзывы:

Похожие инструкции для MUFZ-KJ09NAHZ

Бренды по названию

Популярные бренды