manualshive.com logo in svg

Mitsubishi Electric MELSERVO MR-J4-B-LL Series, Инструкция по эксплуатации

Поделиться
Скачать
Mitsubishi Electric MELSERVO MR-J4-B-LL Series Скачать руководство пользователя страница 8

A -  7 

 
«About the manual» 

You must have this Instruction Manual and the following manuals to use this servo. Be sure to prepare all 
the instruction manuals necessary to use the servo safely. 
Servo amplifiers and drive units are written as servo amplifiers in this manual under certain 
circumstances, unless otherwise stated. 

 

Relevant manuals 

 

Manual name 

Manual No. 

MR-J4-_B(-RJ) Servo Amplifier Instruction Manual 

SH(NA)030106 

MELSERVO-J4 Servo Amplifier Instruction Manual (Troubleshooting) 

SH(NA)030109 

MELSERVO MR-J4-DU_(-RJ)/MR-CR55K_ Instruction Manual (Note 2) 

SH(NA)030153 

MELSERVO Servo Motor Instruction Manual (Vol. 3) (Note 1) 

SH(NA)030113 

EMC Installation Guidelines 

IB(NA)67310 

 

Note   1.  It is necessary for using a rotary servo motor. 
 

  2.  It is necessary for using an MR-J4-DU_B_(-RJ) drive unit and MR-CR55K_ converter unit. 

 

This Instruction Manual does not describe the following items. The following are the same as those for 
MR-J4-_B Servo amplifiers. For the details of the items, refer to each chapter/section indicated in the 
detailed explanation field. "MR-J4-_B_" means "MR-J4-_B_(-RJ) Servo Amplifier Instruction Manual". 
"MR-J4-_DU_" means "MR-J4-DU_(-RJ)/MR-CR55K_ Instruction Manual". 

 

Item Detailed 

explanation 

INSTALLATION 

MR-J4-_B_ chapter 2 
MR-J4-_DU_ chapter 2 

STARTUP 

MR-J4-_B_ chapter 4 
MR-J4-_DU_ chapter 4 

NORMAL GAIN ADJUSTMENT (Note) 

MR-J4-_B_ chapter 6 

SPECIAL ADJUSTMENT FUNCTIONS (Note) 

MR-J4-_B_ chapter 7 

DIMENSIONS 

MR-J4-_B_ chapter 9 
MR-J4-_DU_ chapter 7 

CHARACTERISTICS 

MR-J4-_B_ chapter 10 
MR-J4-_DU_ chapter 8 

ABSOLUTE POSITION DETECTION SYSTEM 

MR-J4-_B_ chapter 12 

USING STO FUNCTION 

MR-J4-_B_ chapter 13 

 

Note. Refer to chapter 4 for adjustment of pressure control. 

 
«Cables used for wiring» 

Wires mentioned in this Instruction Manual are selected based on an ambient temperature of 40 

˚

C. 

 

Содержание MELSERVO MR-J4-B-LL Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды