manualshive.com logo in svg

Mitsubishi Electric MELSERVO MR-J4-B-LL Series, Инструкция по эксплуатации

Поделиться
Скачать
Mitsubishi Electric MELSERVO MR-J4-B-LL Series Скачать руководство пользователя страница 27

1. FUNCTIONS AND CONFIGURATION 

1 -  16 

 

Function Description 

Detailed 

explanation 

Regenerative option 

Use a regenerative option when the built-in regenerative resistor of the servo amplifier 
does not have sufficient regenerative capacity for a large regenerative power 
generated. 

MR-J4-_B_ 
Section 11.2 
MR-J4-_DU_ 
Section 9.2 

Alarm history clear 

Clears alarm histories. 

[Pr. PC21] 

Output signal selection 
(device settings) 

The output devices including ALM (Malfunction) and DB (Dynamic brake interlock) can 
be assigned to certain pins of the CN3 connector. 

[Pr. PD07] 
[Pr. PD08] 

Output signal (DO) forced 
output 

Turns on/off the output signals forcibly independently of the servo status. 
Use this function for checking output signal wiring, etc. 

MR-J4-_B_ 
Section 4.5.1 
(1) (d) 

Test operation mode 

Jog operation, positioning operation, motor-less operation, DO forced output, and 
program operation can be used. MR Configurator2 is necessary for this function. 
Refer to section 6.1 for restrictions when using in the pressure control mode. 

MR-J4-_B_ 
Section 4.5 

Analog monitor output 

Outputs servo status with voltage in real time. 

[Pr. PC09], 
[Pr. PC10] 

MR Configurator2 

Using a personal computer, you can perform the parameter setting, test operation, 
monitoring, and others. 
Refer to section 6.1 for restrictions when using in the pressure control mode. 

Section 6.1 

Linear servo system 

This is not available with the MR-J4-(DU)_B_-LL servo amplifier. 

 

Direct drive servo system 

This is not available with the MR-J4-(DU)_B_-LL servo amplifier. 

 

Fully closed loop system 

This is not available with the MR-J4-(DU)_B_-LL servo amplifier. 

 

One-touch tuning 

Gain adjustment is performed just by one click on MR Configurator2. 
MR Configurator2 is necessary for this function. 
This cannot be used in the pressure control mode. 

MR-J4-_B_ 
Section 6.2 

SEMI-F47 function (Note) 

Enables to avoid triggering [AL. 10 Undervoltage] using the electrical energy charged 
in the capacitor in case that an instantaneous power failure occurs during operation. 
Use a 3-phase for the input power supply of the servo amplifier. Using a 1-phase 100 
V AC/200 V AC for the input power supply will not comply with SEMI-F47 standard. 

[Pr. PA20] 
[Pr. PF25] 
MR-J4-_B_ 
Section 7.4 

Tough drive function 

This function makes the equipment continue operating even under the condition that 
an alarm occurs. 
The tough drive function includes two types: the vibration tough drive and the 
instantaneous power failure tough drive. 
The vibration tough drive cannot be used in the pressure control mode. 

MR-J4-_B_ 
Section 7.3 

Drive recorder function 

This function continuously monitors the servo status and records the status transition 
before and after an alarm for a fixed period of time. You can check the recorded data 
by clicking "Display" under the Waveform column on the drive recorder window on MR 
Configurator2. 
However, the drive recorder is not available when: 
1.  You are using the graph function of MR Configurator2. 
2.  You are using the machine analyzer function. 
3.  [Pr. PF21] is set to "-1". 
4.  The controller is not connected (except the test operation mode). 
5.  An alarm related to the controller is occurring. 

[Pr. PA23] 

STO function 

This function is a functional safety that complies with IEC/EN 61800-5-2. You can 
create a safety system for the equipment easily. 

 

Servo amplifier life diagnosis 
function 

You can check the cumulative energization time and the number of on/off times of the 
inrush relay. This function gives an indication of the replacement time for parts of the 
servo amplifier including a capacitor and a relay before they malfunction. 
MR Configurator2 is necessary for this function. 

 

Power monitoring function 

This function calculates the power running energy and the regenerative power from 
the data in the servo amplifier such as speed and current. Power consumption and 
others are displayed on MR Configurator2. In the SSCNET III/H system, the data are 
sent to a servo system controller for analyzing and displaying the power consumption 
on a display. 

 

Machine diagnosis function 

From the data in the servo amplifier, this function estimates the friction and vibrational 
component of the drive system in the equipment and recognizes an error in the 
machine parts, including a ball screw and bearing. 
MR Configurator2 is necessary for this function. 
This cannot be used in the pressure control mode. 

 

 

Содержание MELSERVO MR-J4-B-LL Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды