manualshive.com logo in svg

Mitsubishi Electric MELSERVO MR-J4-B-LL Series, Инструкция по эксплуатации

Поделиться
Скачать
Mitsubishi Electric MELSERVO MR-J4-B-LL Series Скачать руководство пользователя страница 28

1. FUNCTIONS AND CONFIGURATION 

1 -  17 

 

Function Description 

Detailed 

explanation 

Master-slave operation 
function 

This is not available with the MR-J4-(DU)_B_-LL servo amplifier. 

 

Scale measurement function 

This is not available with the MR-J4-(DU)_B_-LL servo amplifier. 

 

J3 compatibility mode 

This is not available with the MR-J4-(DU)_B_-LL servo amplifier. 
Do not change the mode by using the application software "MR-J4(W)-B mode 
selection". An error appears when the mode is changed to other than the J4 mode 
(standard control (rotary servo motor)). 

 

Continuous operation to 
torque control mode 

This is not available with the MR-J4-(DU)_B_-LL servo amplifier. 

 

Lost motion compensation 
function 

This function improves the response delay occurred when the machine moving 
direction is reversed. 
This is available with servo amplifiers with software version B4 or later. Check the 
software version with MR Configurator2. 
This cannot be used in the pressure control mode. 

MR-J4-_B_ 
Section 7.6 

Super trace control 

This is not available with the MR-J4-(DU)_B_-LL servo amplifier. 

 

 

Note. For servo system controllers which are available with this, contact your local sales office. 

 

Содержание MELSERVO MR-J4-B-LL Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды