manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-RD77GF16, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric MELSEC iQ-RD77GF16 Скачать руководство пользователя страница 24

22

2  SPECIFICATIONS
2.1  Performance Specifications of the RD77MS

2

SPECIFICATIONS

This chapter describes the performance specifications of the RD77MS and the RD77GF.

2.1

Performance Specifications of the RD77MS

This section lists the performance specifications of the RD77MS.

Item

RD77MS2

RD77MS4

RD77MS8

RD77MS16

Number of controlled axes

2 axes

4 axes

8 axes

16 axes

Operation cycle

0.444 ms/0.888 ms/1.777 ms/3.555 ms

Interpolation function

2-axis linear 
interpolation, 2-axis 
circular interpolation

2-, 3-, or 4-axis linear interpolation, 2-axis circular interpolation, 3-axis 
helical interpolation

Control method

PTP (Point To Point) control, path control (linear, arc, and helix can be set), speed control, speed-
position switching control, position-speed switching control, speed-torque control

Control unit

mm, inch, degree, pulse

Positioning data

600 data/axis (The 101st data to the 600th data can be set only with the engineering tool.)

Execution data backup function

Parameters, positioning data, and block start data can be saved on flash ROM. (battery-less backup)

Positioning

Positioning system

PTP control: Incremental system/absolute system
Speed-position switching control: Incremental system/absolute system
Position-speed switching control: Incremental system
Path control: Incremental system/absolute system

Positioning range

In absolute system

• -214748364.8 to 214748364.7 (

m)

• -21474.83648 to 21474.83647 (inch)
• 0 to 359.99999 (degree)
• -2147483648 to 2147483647 (pulse)

In incremental system

• -214748364.8 to 214748364.7 (

m)

• -21474.83648 to 21474.83647 (inch)
• -21474.83648 to 21474.83647 (degree)
• -2147483648 to 2147483647 (pulse)

In speed-position switching control (INC mode)/position-speed switching control

• 0 to 214748364.7 (

m)

• 0 to 21474.83647 (inch)
• 0 to 21474.83647 (degree)
• 0 to 2147483647 (pulse)

In speed-position switching control (ABS mode)

*1

0 to 359.99999 (degree)

Speed command

0.01 to 20000000.00 (mm/min)
0.001 to 2000000.000 (inch/min)
0.001 to 2000000.000 (degree/min)

*2

1 to 1000000000 (pulse/s)

Acceleration/deceleration process

Trapezoidal acceleration/deceleration, S-curve acceleration/deceleration

Acceleration/deceleration time

1 to 8388608 (ms) (Four patterns can be set for each of acceleration time and deceleration time.)

Rapid stop deceleration time

1 to 8388608 (ms)

Содержание MELSEC iQ-RD77GF16





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды