Mitsubishi Electric MELSEC iQ-F FX55-ASL-M Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 96

background image

7 PARAMETER SETTINGS

7.5 Automatic Address Detection Function

55

7

7.5

Automatic Address Detection Function

Automatic address detection refers to a function that stores the IDs (addresses) of the connected slave modules in the
EEPROM of the FX5-ASL-M.
Pressing the SET switch on the FX5-ASL-M enables this function and enables the FX5-ASL-M to detect and store IDs
(addresses) of connected slave modules.
The ID (address) information stored in the EEPROM is held even when the power is turned off. However, information about
unset IDs, the same IDs, and the parameter information of each slave module are not held.
Whenever starting the system or changing the system configuration, set the correct addresses to all the slave modules and
execute the automatic address detection.

Executing the automatic address detection

To execute the automatic address detection, use the SET switch or 'Automatic address detection command' (Un/G27 b1).

Using the SET switch

1.

Check that all of the slave modules are operating normally.

2.

Keep pressing the SET switch on the FX5-ASL-M until the SET LED turns on.

At this time, 'Automatic address detection flag' (Un\G28 b11) turns on.

3.

When the SET LED flashes for a while and turns off, the ID (address) has been stored.

4.

When 'Automatic address detection flag' (Un\G28 b11) turns off, the automatic address detection is completed.

Using 'Automatic address detection command' (Un\G27 b1)

1.

Check that all of the slave modules are operating normally.

2.

Turn on and off 'Automatic address detection command' (Un\G27 b1).

At this time, 'Automatic address detection flag' (Un\G28 b11) turns on.

3.

When the SET LED flashes for a while and turns off, the ID (address) has been stored.

4.

When 'Automatic address detection flag' (Un\G28 b11) turns off, the automatic address detection is completed.

«
...
55
56
57
58
59
...
»

Содержание MELSEC iQ-F FX55-ASL-M

































































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC iQ-F FX55-ASL-M

Бренд: Faber Страницы: 8

Бренд: Waterway Страницы: 16

Бренд: Samson Страницы: 40

Бренд: Rain Bird Страницы: 4

Бренд: Rain Bird Страницы: 2

Бренд: Rain Bird Страницы: 140

WeatherSmart RSC600i

Бренд: Raindrip Страницы: 36

Бренд: KEENZ Страницы: 68

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 21

Бренд: M&S Systems Страницы: 4

Бренд: Dakota Digital Страницы: 12

Бренд: FUTABA Страницы: 8

ibaMS16-DI-220V Series

Бренд: IBA Страницы: 32

Бренд: Festo Страницы: 62

Бренд: Peg-Perego Страницы: 68

Sundstrom SR307

Бренд: S.E.A. Group Страницы: 5

Ratio Feeder J+ Advanced Series

Бренд: H.E. Anderson Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды