Mitsubishi Electric MELSEC iQ-F FX55-ASL-M Скачать руководство пользователя страница 27

Страница: 27 / 96

4 FUNCTION

4.4 Remote Address Change Function

4.4

Remote Address Change Function

With this function, an ID (address) of a slave module can be changed using the buffer memory area without an address writer.

Applicable slave module

For the slave modules that support the remote address change function, contact Anywire Corporation.

Operating procedure

Execute automatic address detection to check that no error has occurred in the AnyWireASLINK system. (



Page 55

Automatic Address Detection Function)

Specify an access method to a slave module.

Store 0002H (address change) in 'Parameter access setting' (Un\G10320).

Specify an ID of the slave module to be accessed.

Store the ID to be changed (old ID) in 'Parameter access target module ID specification' (Un\G10321).

Specify a new ID of the slave module.

Store the new ID in 'Change ID specification' (Un\G10323).

If the specified ID has already been used or is out of the allowable specification range, an error occurs.

Turn on and off 'Parameter access request command for the slave module' (Un\G27 b8).

At this time, 'Parameter access completion flag' (Un\G28 b9) turns off. When the parameter access is completed, 'Parameter
access completion flag' (Un\G28 b9) automatically turns on.

After changing the IDs of all the target slave modules, execute automatic address detection. (



Page 55 Automatic

Address Detection Function)

Precautions

• Before executing this function, make sure to execute automatic address detection to check that no error has occurred in the

AnyWireASLINK system. (



Page 55 Automatic Address Detection Function)

• This function cannot be executed for slave modules separated from the FX5-ASL-M because of disconnection or slave

modules having the same ID. Use an address writer to change the IDs of such slave modules.

• This function can be executed if only one slave module having no ID exists within one AnyWireASLINK line. If IDs of

multiple slave modules are not set, it is recognized as an ID duplication. Thus, the IDs cannot be changed.

Description

0000H to 00FFH

ID of the output slave module

0200H to 02FFH

ID of the input slave module or I/O combined slave module

Description

0000H to 00FFH

ID of the output slave module

0200H to 02FFH

ID of the input slave module or I/O combined slave module

0200H 0210H

Содержание MELSEC iQ-F FX55-ASL-M

































































































Результаты поиска

Содержание MELSEC iQ-F FX55-ASL-M

Отзывы:

Похожие инструкции для MELSEC iQ-F FX55-ASL-M

Бренды по названию

Популярные бренды

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M, Руководство пользователя

Результаты поиска

Содержание MELSEC iQ-F FX55-ASL-M

Отзывы:

Похожие инструкции для MELSEC iQ-F FX55-ASL-M

Бренды по названию

Популярные бренды