manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric MELSEC iQ-F FX55-ASL-M Скачать руководство пользователя страница 82

80

APPX
Appendix 4  Buffer Memory

Latest error code storage area

■

Latest error code storage area (Un\G10256)

This buffer memory area stores the latest error code detected in the FX5-ASL-M. For details on the error codes, refer to the 
following.

Page 69 List of Error Codes

Latest error ID storage area

■

Latest error ID storage area (Un\G10257)

This buffer memory area stores the error ID corresponding to the latest error code that occurred.
 • Relation of error code and error ID

Parameter access setting

■

Parameter access setting (Un\G10320)

Specify the parameter access method. When a value other than those below is stored, the parameter is read.
 • 0000H: Read (slave module 

 FX5-ASL-M 

 CPU module)

 • 0001H: Write (CPU module 

 FX5-ASL-M 

 slave module)

 • 0002H: Address change (CPU module 

 FX5-ASL-M 

 slave module)

Parameter access target module ID specification

■

Parameter access target module ID specification (Un\G10321)

Specify the access ID for accessing the parameters of individual IDs.
Write one of the following to specify the ID.
 • 0000H to 00FFH: ID of an output slave module
 • 0200H to 02FFH: ID of an input slave module or I/O combined slave module

Change ID specification

■

Change ID specification (Un\G10323)

Specify a new ID (address) with the remote address change function.
Write one of the following to specify the ID.
 • 0000H to 00FFH: ID of an output slave module
 • 0200H to 02FFH: ID of an input slave module or I/O combined slave module

Error code 
(hexadecimal)

Description of error

Value of the error ID storage area

1867H
3064H
3065H
3066H

FX5-ASL-M hardware failure

 (Buffer memories cannot be accessed.)

0CC8H

Transmission cable voltage drop error

0FFFH (4095)
Error contents without regard to the ID

0CC9H

DP/DN short error

0FFFH (4095)
Error contents without regard to the ID

0CCAH

DP/DN disconnection error

Error ID

0CCBH

24V/DP short error

0FFFH (4095)
Error contents without regard to the ID

0D2CH
0D2DH

Slave module hardware error

Error ID

0D2EH

Parameter access target module ID error

0FFFH (4095)
Error contents without regard to the ID

0D2FH

Parameter value error

Error ID

0D30H

Parameter access error

Error ID

0D31H

Slave module status error

Error ID

0D90H

Same ID used error

Error ID

0D91H

No ID setting error

Error ID

Содержание MELSEC iQ-F FX55-ASL-M

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды