manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M, Руководство пользователя

Получите бесплатное руководство пользователя "Mitsubishi Electric MELSEC iQ-F FX55-ASL-M" на нашем сайте. Скачайте его прямо сейчас, чтобы легко ознакомиться с функционалом этого продукта. Необходимая информация доступна для скачивания на manualshive.com.

Поделиться
Скачать
background image

22

4  FUNCTION
4.1  Function List

4

FUNCTION

4.1

Function List

The following table lists the function available for the FX5-ASL-M.

AnyWireASLINK transmission

Address setting

RAS

Others

Function

Description

Reference

Bit transmission

Exchanges I/O data of up to 384 points (input max. 256 points, output max. 256 points) 
between the FX5-ASL-M and a slave module.

Page 23

Double check

A double check is an error control system. In this system, cycle data in AnyWireASLINK 
transmission is recognized as valid data if the data matches with the data of the last 
transmission or is ignored as invalid data if the data does not match with the last data.
A double check ensures reliability of communication.

Page 24

Slave module parameter read/write

In AnyWireASLINK, parameter information of a slave module and the AnyWireASLINK system 
in addition to I/O information are sent and received between the FX5-ASL-M and a slave 
module.
Execute this function to check or change parameter information of a slave module.

Page 35

Function

Description

Reference

Automatic address detection function

Enables the FX5-ASL-M to detect and store the ID (address) of the connected slave module 
when the SET switch on the FX5-ASL-M is pressed.

Page 55

Remote address change function

Changes an ID (address) of a slave module using the buffer memory area without an address 
writer.

Page 25

Same ID used detection function

Checks whether the same ID is used for multiple slave modules through automatic address 
detection or same address used check. The LEDs of the relevant slave modules are forcibly 
turned on.

Page 26

Module with no ID setting detection 
function

Detects slave modules with no ID assigned (default ID) through automatic address detection 
or same address used check.

Page 28

Function

Description

Reference

Transmission cable short detection 
function

Protects the system by detecting the current out of the specifications of the AnyWireASLINK 
system across DP-DN or 24V-DP and stopping the transmission.

Page 29

Disconnected transmission cable 
location detection function

Notifies the ID of a slave module that has been separated from the FX5-ASL-M because of 
disconnection in the transmission cables (DP, DN) between the FX5-ASL-M and the slave 
module, to locate the disconnection in the transmission cables (DP, DN) from the upper 
system.

Page 30

Transmission cable voltage drop 
detection function

Detects a voltage drop in the 24 V DC external power supply, enabling the FX5-ASL-M to 
detect a failure in the 24 V DC external power supply or a wiring error from the upper system.

Page 31

Function

Description

Reference

Parameter access error detection 
function

Allows parameter access errors to be detected.

Page 32

Error status automatic recovery 
function

Allows for automatic error reset for DP/DN disconnection errors and parameter errors after the 
error status is cleared.

Page 34

Slave information acquisition at start-
up function

Allows for automatic acquisition of information of slave modules when the CPU module is 
reset or power off and on the system.

Page 34

Содержание MELSEC iQ-F FX55-ASL-M

































































































Отзывы:

Нет отзывов

Похожие инструкции для MELSEC iQ-F FX55-ASL-M

Radarcan R-200 User Manual preview
R-200
Бренд: Radarcan Страницы: 40
Jeep Liberty Instruction Sheet preview
Liberty
Бренд: Jeep Страницы: 32
Accel 300+ Installation Instructions Manual preview
300+
Бренд: Accel Страницы: 8
tams elektronik HELIOS Manual preview
HELIOS
Бренд: tams elektronik Страницы: 60
Parker CHELSEA Owner'S Manual preview
CHELSEA
Бренд: Parker Страницы: 32
Rayrun NT30 Quick Start Manual preview
NT30
Бренд: Rayrun Страницы: 4
PACH & COMPANY AeGIS 7000 Series Quick Start Manual preview
AeGIS 7000 Series
Бренд: PACH & COMPANY Страницы: 2
Zeta Premier MX-16 Installation And Commissioning Manual preview
Premier MX-16
Бренд: Zeta Страницы: 44
Polycom VVX Series Basic Troubleshooting preview
VVX Series
Бренд: Polycom Страницы: 2
Baninni BN-1266 MILANO Instruction Manual preview
BN-1266 MILANO
Бренд: Baninni Страницы: 5
Daihan Scientific WHM-C10D Operation Manual preview
WHM-C10D
Бренд: Daihan Scientific Страницы: 11
Eaton Cutler-Hammer LMR Instructions Manual preview
Cutler-Hammer LMR
Бренд: Eaton Страницы: 38
HEROSE 05411 Operating Instructions Manual preview
05411
Бренд: HEROSE Страницы: 92
Bardiani BBZS5 Operating And Maintenance Instructions Manual preview
BBZS5
Бренд: Bardiani Страницы: 22
Samlex Solar DC-BTS-A-C Owner'S Manual preview
DC-BTS-A-C
Бренд: Samlex Solar Страницы: 3
Dataq DI-1000TC User Manual preview
DI-1000TC
Бренд: Dataq Страницы: 26
Anritsu NF7600 Series Operation Manual preview
NF7600 Series
Бренд: Anritsu Страницы: 74
Adaptec ASR-2045 Important Information About Issues And Errata preview
ASR-2045
Бренд: Adaptec Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды