Mitsubishi Electric DXK09ZJ-S Скачать руководство пользователя страница 42

Страница: 42 / 115

'11 • SRK-T-118

'09•SRK-DB-087D

Operation section

1 OUTLINE OF OPERATION CONTROL BY MICROCOMPUTER

1. Operation control function by remote controller

FAN SPEED button

Each time the button is pressed, the

display is switched over in turn.

OPERATION MODE select button

Each time the button pressed, the

display is switched over in turn.

ON/OFF (luminous) button

Press to start operation, press again to

stop.

HI POWER/ECONO button

This button changes the HIGH POWER/

ECONOMY mode.

AIR FLOW (UP/DOWN) button

This button changes the air flow (up/down)

direction.

This button changes the air flow (left/right)

direction.

SLEEP button

This button selects SLEEP operation.

CLEAN switch

This switch changes the CLEAN mode.

ON TIMER button

This button selects ON TIMER operation.

AIR FLOW (LEFT/RIGHT) button

3D AUTO button

This button sets 3D AUTO operation.

This button selects ALLERGEN CLEAR

operation.

ALLERGEN CLEAR button

ACL switch

This switch is for resetting microcomputer

and setting time.

OFF TIMER button

This button selects OFF TIMER operation

TEMPERATURE button

These buttons sets the indoor temperature.
(These buttons are used for setting the

current time and timer function as well.)

This button cancels the ON timer, OFF

timer, and SLEEP operation.

CANCEL button

The above illustration shows all controls, but in practice

only the relevant parts are shown.

Unit display section

3D AUTO light (green)

Illuminates during 3D AUTO operation.

HI POWER light (green)

Illuminates during HIGH POWER operation.

TIMER light (yellow)

Illuminates during TIMER operation.

This button can be used for turning on/off the unit when remote
control is not available.

Remote control signal receiver

Unit ON/OFF button

RUN (HOT KEEP) light (green)

࡮

Illuminates during operation.

࡮

Blinks when airflow stops due to the

HOT

KEEP

and

CLEAN operation

OFF

1.5 sec.

0.5 sec.

HOT KEEP

3 sec.

1 sec.

OFF

CLEAN operation

Reference

9. OUTLINE OF OPERATION CONTROL BY MICROCOMPUTER

(1) Operation control function by remote controller

Содержание DXK09ZJ-S




















































































































Результаты поиска

Содержание DXK09ZJ-S

Отзывы:

Похожие инструкции для DXK09ZJ-S

Бренды по названию

Популярные бренды

Mitsubishi Electric DXK09ZJ-S, Техническое руководство

Результаты поиска

Содержание DXK09ZJ-S

Отзывы:

Похожие инструкции для DXK09ZJ-S

Бренды по названию

Популярные бренды