Mitsubishi Electric DXK09ZJ-S Скачать руководство пользователя страница 84

Страница: 84 / 115

'11 • SRK-T-118

DO NOT install the interface and wired remote controller at the

following places.

○

Places exposed to direct sunlight

○

Places near heating devices

○

High humidity places

○

Surfaces where are enough hot or cold to generate condensation

○

Places exposed to oil mist or steam directly

①

Mount the lower casing of the interface on a flat surface with wood

screws provided as standard accessory.

②

Mount the upper casing.

○

Uneven surface

①

Mount it on a wall or a pillar

with 2 of wood screws

②

Mount it to the electrical box

with 2 of M4 screws

(procured locally)

②

Mount the

upper casing

③

Mount the upper casing

Electrical box

(procured locally)

Connection cable

Wiring inlet

Installation check items

Mounting the interface with the mounting bracket

Mounting the interface directly on a wall

Recessing the interface in the wall

・

Install the interface within the range of the connection cable length

(approximately 1.3m) from the indoor unit.

・

Be sure not to extend the connection cable on site. If the connection

cable is extended, malfunction may occur.

・

Fix the interface on the wall, pillar or the like.

Cut out the punch-outs

for the connection cables

running into the casing

with cutter

①

Recess the electrical box (locally procured) and

connection cables in the wall.

②

Mount the lower casing of the interface to the

electrical box with M4 screws (locally procured).

③

Mount the upper casing.

①

Mount the mounting bracket to the interface with tapping

screws provided as standard accessory.

②

Mount the mounting bracket on wall or the like with wood

screws provided as standard accessory.

③

Mount the mounting bracket to a wall surface, etc.

using the wood screws provided.

□

Are the connection cables connected securely to the terminal blocks and connectors?

□

Are the thickness and length of the connection cables conformed with the standard?

Installation of the interface

①

Recess the electrical

box and connection cables

②

Mount the mounting

bracket on the interface

with 2 of tapping screws

③

Mount the bracket on

a wall or a pillar with

2 of wood screws

Содержание DXK09ZJ-S




















































































































Результаты поиска

Содержание DXK09ZJ-S

Отзывы:

Похожие инструкции для DXK09ZJ-S

Бренды по названию

Популярные бренды

Mitsubishi Electric DXK09ZJ-S, Техническое руководство

Результаты поиска

Содержание DXK09ZJ-S

Отзывы:

Похожие инструкции для DXK09ZJ-S

Бренды по названию

Популярные бренды