MAINTENANCE Menu
Appendix B
Controller Menus
LEVEL
Set the tank level in the controller display from 1 to 8 bars.
In operation, the indicated level will decrease as insecticide
is misted. Hold Green
►
button for 5 seconds, then
▲
and
▼
buttons to set.
INS
Inspect Nozzle Circuit. Runs pump for 5 minutes. Hold
Green
►
button for 5 seconds to trigger. If Zone Kit
installed, separate inspection menus, INS1 and INS2.
Appendix B
Controller Menus
Set the Day of the Week and the Time of Day
and Daylight Savings Time switch.
DAY/TIME Menu
Configure the mist time and duration of each of
24 possible Auto Mist Cycles (Each with unique
duration and time of day.)
CYCLES Menu
Configures the days of the week for Auto
Misting in the AUTO-CUSTOM PGM
mode. (Turn each day OFF or ON.)
CUSTOM PGM Menu
REM
Set the duration for mists triggered by the remote
transmitter. (Values from OFF to 120 seconds)
LRN
Program unit to recognize a specific remote transmitter.
Hold down Green
►
button for 5 seconds and then press
a button on the remote transmitter. When DONE flashes
in the display, the transmitter is programmed.
MAN
Set the duration for mists triggered by a Manual Mist
(pressing
▲
and
▼
buttons simultaneously.)
NOZ
Set the Number of nozzles in the circuit attached to the
unit. If Zone Kit installed, there are separate displays for
NZ1 and NZ2.
AGT
Set duration in seconds of agitation prior to programmed
mists and set time of once daily off-cycle agitation. On
units without an agitating valve, the duration should be set
to 0.
RAG
Set duration in seconds of agitation cycle prior to a remote
mist cycle. (RAG not available on pre-2012 systems.)
TNK
Set reservoir size in gallons (5 – 995)
SEN
Turn (optional) wind sensor ON or OFF
WND
Set max wind speed (above which wind sensor reading
inhibits mist).
ALT
This feature is not currently used. ALT should be set to 0.
SET-UP Menu (systems without zone kit)*
* For systems with zone kit installed, refer to system setup
instructions included with zone kit hardware.
DATA Menu
(Items marked ** are for units equipped with leak detection)
TMC
Total Mist Cycles since last reset.*
TMM
Total Mist Minutes since last reset.*
MMC
Manual Mist Cycles since last reset.*
RMC
Remote Mist Cycles since last reset.*
TMH
Total Mist Hours on unit. May not be reset.
FL**
Actual volume pumped out of tank during last mist (mL).
TF**
Calculated target volume in milliliters (mL) of last mist.
Target Volume = (Mist Duration in seconds) * (Number of
Nozzles) * (Nozzle Flow Rate NFR) / 60.
SPD
Wind speed as read by sensor.
AFR**
Actual average flow rate of nozzle in circuit, based on
volume of fluid discharged during last mist cycle.
TOL**
Error tolerance for nozzle circuit flow rate. Default is 75%.
Controls sensitivity of leak detection. (Set as per NFR).
NFR
Target flow rate of average nozzle in circuit, in milliliters per
minute. Used in tank level indicator, Empty shut-off and
leak detection calculations. Default is 40 mL/min. Set by
pressing Green
►
button for 5 seconds, then
▲
and
▼
arrows to adjust, then Green
►
button to save.
HLD
Duration that Agitating Valve or Anti-Siphon Valve remains
open to nozzle circuit after pump shuts off. Used to control
“at-rest” pressure maintained in circuit. (Set as per NFR).
*
Reset by pushing Green
►
button until value shows zero.
NOTE
:
PAN, FR, NR
and
L
menu items are for factory configuration only.
